RTL8139 NIC Not Working

[snake eyes]

Sorry about this really long text..but trying to give as much detail as possible
Still a newbie with linux
Configuration of my PC:

Intel Pentium 2.66Ghz
Asus P5RDVM Motherboard with X900 Chipset
XFX's NVidia 6200TC Card
(But using 8400 currently)
512MB RAM
One 100MB NIC on PCI slot (Motherboard has another onboard but its faulty.)
Western Digital 160GB SATA
Seagate 20GB PATA

4 Windows partitions on WD dsik with WIndows XP Pro installed on 1st partition

Now I wanted to install BT3 without messing up my XP installation. Still a newbie to Linux and can't just migrate to Linux as yet.

I installed Acronis disk director and made 3 more partitions. One 1Gb for Linux swap , one 12GB ReiserFS for BT3 and made one 6GB empty space

I also installed Acronis boot loader, just to be safe
Now my previous attempts to successfuly make my PC dualbootable failed with BT. So I thought of installing Ubuntu Linux too. First I booted from an Ubuntu CD and installed it on HDD. In installation process I selected use the largest available free space.
It used that 6GB free space to install itself. After installation I rebooted the PC and was promptly greeted with a GRUB menu with booting options for both XP and Ubuntu.

Now its time for BT3.
Booted using Backtrack 3 DVD. Since I had already made partitions I didnt need to make new using fdiask command.
Just used "Install BT to HD " option from its start menu.

The 12Gb ReiserFS partition was /dev/sda5. Used that for installing BT and /dev/sda for installing MBR. Used full install and unchecked "remove from MBR" option. It took like 10-15 minutes for install.

Rebooted and bumped into LILO boot loader of BT.

Ubuntu and Windows nowhere visible.


Booted into BT and logged in using default password.

type "liloconfig" and selected new LILO installatiion



Booted into BT and logged in using default password.
type "liloconfig" and selected new LILO installatiion
In next menu selected Add Windows Installation and added /dev/sda1
For Ubuntu added /dev/sda8 and "dev/sda5" for BT
Note that these sda will differ for different PCs. Could be hda if you have PATA disk or sda 1,2,3 etc may differ.


Saved and rebooted

This time I got Acronis boot loader menu

But with only 2 choices
One Windows XP and other Linux
Selected Linux and got LILO of BT3 . But this time with 3 options. Windows, Ubuntu and backTrack3
ALl working perfectly

Except for one small part..NIC not working properly.
I fill in proper IP address, gateway etc..but cant ping my gateway even.
Turns out both Linux picked up my onboard NIC (it was fried n a lightning storm).
My other NIC Realtek 8139 (this works) wasnt detected by either Linux

I then disabled my onboard NIC from BIOS and booted int BT. This time ifconig sommand showed only the l0 not eth0
I downloaded drivers of that card and tried installing them..but the error is get is

bt sc92031 # make
Makefile:37: *** Linux kernel source not configured - missing config.h. Stop.

I tried running

acpi=noirq

before running startx. but that didnt help either


I installed other software, openssl, medusa etc and they got installed without any problem

[snake eyes]

bt sc92031 # lsmod
Module Size Used by
snd_seq_dummy 6660 0
snd_seq_oss 32768 0
snd_seq_midi_event 10112 1 snd_seq_oss
snd_seq 49872 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_seq_device 10508 3 snd_seq_dummy,snd_seq_oss,snd_seq
snd_pcm_oss 42656 0
snd_mixer_oss 17920 1 snd_pcm_oss
pcmcia 35244 0
pcmcia_core 36628 1 pcmcia
capability 7304 0
commoncap 9344 1 capability
fuse 41876 6
lp 13864 0
parport_pc 27940 1
parport 34888 2 lp,parport_pc
pcspkr 6400 0
psmouse 38792 0
hci_usb 18588 0
serio_raw 9220 0
bluetooth 52964 1 hci_usb
i2c_ali1535 10116 0
i2c_ali15x3 10756 0
snd_hda_intel 20248 0
snd_hda_codec 211712 1 snd_hda_intel
snd_pcm 71428 3 snd_pcm_oss,snd_hda_intel,snd_hda_codec
ati_agp 10892 0
ata_generic 9220 0
snd_timer 22276 2 snd_seq,snd_pcm
agpgart 31304 1 ati_agp
snd 46692 9 snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd _mixer_oss,snd_hda_intel,snd_hda_codec,snd_pcm,snd _timer
soundcore 9824 1 snd
snd_page_alloc 11400 2 snd_hda_intel,snd_pcm
pata_ali 12296 0
shpchp 33300 0
sg 30364 0
evdev 12032 3

bt sc92031 # grep
Usage: grep [OPTION]... PATTERN [FILE]...
Try `grep --help' for more information.
bt sc92031 # lspci
00:00.0 Host bridge: ATI Technologies Inc Radeon Xpress 200 Host Bridge (rev 01)
00:02.0 PCI bridge: ATI Technologies Inc RS480 PCI-X Root Port
00:19.0 PCI bridge: ALi Corporation M5249 HTT to PCI Bridge
00:1c.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:1c.1 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:1c.2 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:1c.3 USB Controller: ALi Corporation USB 2.0 Controller (rev 01)
00:1d.0 Audio device: ALi Corporation High Definition Audio/AC'97 Host Controller
00:1e.0 ISA bridge: ALi Corporation PCI to LPC Controller (rev 31)
00:1e.1 Bridge: ALi Corporation M7101 Power Management Controller [PMU]
00:1f.0 IDE interface: ALi Corporation M5229 IDE (rev c7)
00:1f.1 RAID bus controller: ALi Corporation ULi 5287 SATA (rev 02)
01:00.0 VGA compatible controller: nVidia Corporation GeForce 8400 GS (rev a1)
02:13.0 Ethernet controller: Hangzhou Silan Microelectronics Co., Ltd. RTL8139D [Realtek] PCI 10/100BaseTX ethernet adaptor (rev 01)

bt sc92031 # lsmod | grep
Usage: grep [OPTION]... PATTERN [FILE]...
Try `grep --help' for more information.
bt sc92031 # lsmod | grep 8139
bt sc92031 # lsmod
Module Size Used by
snd_seq_dummy 6660 0
snd_seq_oss 32768 0
snd_seq_midi_event 10112 1 snd_seq_oss
snd_seq 49872 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_seq_device 10508 3 snd_seq_dummy,snd_seq_oss,snd_seq
snd_pcm_oss 42656 0
snd_mixer_oss 17920 1 snd_pcm_oss
pcmcia 35244 0
pcmcia_core 36628 1 pcmcia
capability 7304 0
commoncap 9344 1 capability
fuse 41876 6
lp 13864 0
parport_pc 27940 1
parport 34888 2 lp,parport_pc
pcspkr 6400 0
psmouse 38792 0
hci_usb 18588 0
serio_raw 9220 0
bluetooth 52964 1 hci_usb
i2c_ali1535 10116 0
i2c_ali15x3 10756 0
snd_hda_intel 20248 0
snd_hda_codec 211712 1 snd_hda_intel
snd_pcm 71428 3 snd_pcm_oss,snd_hda_intel,snd_hda_codec
ati_agp 10892 0
ata_generic 9220 0
snd_timer 22276 2 snd_seq,snd_pcm
agpgart 31304 1 ati_agp
snd 46692 9 snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd _mixer_oss,snd_hda_intel,snd_hda_codec,snd_pcm,snd _timer
soundcore 9824 1 snd
snd_page_alloc 11400 2 snd_hda_intel,snd_pcm
pata_ali 12296 0
shpchp 33300 0
sg 30364 0
evdev 12032 3

bt sc92031 # ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

bt sc92031 # lsmod | grep 8139

bt sc92031 # lsmod
Module Size Used by
snd_seq_dummy 6660 0
snd_seq_oss 32768 0
snd_seq_midi_event 10112 1 snd_seq_oss
snd_seq 49872 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_seq_device 10508 3 snd_seq_dummy,snd_seq_oss,snd_seq
snd_pcm_oss 42656 0
snd_mixer_oss 17920 1 snd_pcm_oss
pcmcia 35244 0
pcmcia_core 36628 1 pcmcia
capability 7304 0
commoncap 9344 1 capability
fuse 41876 6
lp 13864 0
parport_pc 27940 1
parport 34888 2 lp,parport_pc
pcspkr 6400 0
psmouse 38792 0
hci_usb 18588 0
serio_raw 9220 0
bluetooth 52964 1 hci_usb
i2c_ali1535 10116 0
i2c_ali15x3 10756 0
snd_hda_intel 20248 0
snd_hda_codec 211712 1 snd_hda_intel
snd_pcm 71428 3 snd_pcm_oss,snd_hda_intel,snd_hda_codec
ati_agp 10892 0
ata_generic 9220 0
snd_timer 22276 2 snd_seq,snd_pcm
agpgart 31304 1 ati_agp
snd 46692 9 snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd _mixer_oss,snd_hda_intel,snd_hda_codec,snd_pcm,snd _timer
soundcore 9824 1 snd
snd_page_alloc 11400 2 snd_hda_intel,snd_pcm
pata_ali 12296 0
shpchp 33300 0
sg 30364 0
evdev 12032 3

any ideas???

[snake eyes]

dmesg command

bt ~ # dmesg
Linux version 2.6.21.5 (root@bt) (gcc version 4.1.2) #2 SMP Sat Aug 25 19:01:21 GMT 2007
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
copy_e820_map() start: 00000000000e0000 size: 0000000000020000 end: 0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000001feb0000 end: 000000001ffb0000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000001ffb0000 size: 000000000000e000 end: 000000001ffbe000 type: 3
copy_e820_map() start: 000000001ffbe000 size: 0000000000022000 end: 000000001ffe0000 type: 4
copy_e820_map() start: 000000001ffe0000 size: 0000000000020000 end: 0000000020000000 type: 2
copy_e820_map() start: 00000000ff780000 size: 0000000000880000 end: 0000000100000000 type: 2
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffb0000 (usable)
BIOS-e820: 000000001ffb0000 - 000000001ffbe000 (ACPI data)
BIOS-e820: 000000001ffbe000 - 000000001ffe0000 (ACPI NVS)
BIOS-e820: 000000001ffe0000 - 0000000020000000 (reserved)
BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
found SMP MP-table at 000ff780
Entering add_active_range(0, 0, 130992) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 130992
HighMem 130992 -> 130992
early_node_map[1] active PFN ranges
0: 0 -> 130992
On node 0 totalpages: 130992
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 991 pages used for memmap
Normal zone: 125905 pages, LIFO batch:31
HighMem zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000FB1A0, 0014 (r0 ACPIAM)
ACPI: RSDT 1FFB0000, 0034 (r1 A M I OEMRSDT 3000624 MSFT 97)
ACPI: FACP 1FFB0200, 0084 (r2 A M I OEMFACP 3000624 MSFT 97)
ACPI Warning (tbfadt-0360): Ignoring BIOS FADT r2 C-state control [20070126]
ACPI: DSDT 1FFB0440, 5448 (r1 A0313 A0313001 1 INTL 2002026)
ACPI: FACS 1FFBE000, 0040
ACPI: APIC 1FFB0390, 006C (r1 A M I OEMAPIC 3000624 MSFT 97)
ACPI: MCFG 1FFB0400, 003C (r1 A M I OEMMCFG 3000624 MSFT 97)
ACPI: OEMB 1FFBE040, 004B (r1 A M I AMI_OEM 3000624 MSFT 97)
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:4 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.

[snake eyes]

dmesg reort contd

Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:df780000)
Built 1 zonelists. Total pages: 129969
Kernel command line: BOOT_IMAGE=BackTrack ro root=805
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 2720.662 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 509980k/523968k available (6006k kernel code, 13472k reserved, 1918k data, 388k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xffe16000 - 0xfffff000 (1956 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
lowmem : 0xc0000000 - 0xdffb0000 ( 511 MB)
.init : 0xc08c6000 - 0xc0927000 ( 388 kB)
.data : 0xc06dd83d - 0xc08bd3ac (1918 kB)
.text : 0xc0100000 - 0xc06dd83d (6006 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5447.53 BogoMIPS (lpj=10895065)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000651d 00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Hyper-Threading is disabled
CPU: After all inits, caps: bfebfbff 20000000 00000000 00003180 0000651d 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code

[snake eyes]

dmesg contd

Freeing SMP alternatives: 23k freed
ACPI: Core revision 20070126
CPU0: Intel(R) Pentium(R) 4 CPU 2.66GHz stepping 09
Total of 1 processors activated (5447.53 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 4000-403f claimed by ali7101 ACPI
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE2P._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15), disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15), disabled.
ACPI: PCI Interrupt Link [LNKP] (IRQs 3 4 5 6 7 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
SCSI subsystem initialized
libata version 2.20 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 9 of bridge 0000:00:02.0
PCI: Cannot allocate resource region 3 of device 0000:00:00.0
PCI: Cannot allocate resource region 1 of device 0000:01:00.0
pnp: 00:07: iomem range 0xfff80000-0xffffffff could not be reserved
pnp: 00:07: iomem range 0xffb00000-0xffbfffff could not be reserved
pnp: 00:07: iomem range 0xc0000000-0xc0000fff has been reserved
pnp: 00:07: iomem range 0xff6fe000-0xff6fefff has been reserved
pnp: 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
pnp: 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved
pnp: 00:0c: ioport range 0xc00-0xc0f has been reserved
pnp: 00:0c: ioport range 0xd00-0xd0f has been reserved
pnp: 00:0c: ioport range 0xa20-0xa2f has been reserved
pnp: 00:0c: ioport range 0xa30-0xa3f has been reserved
pnp: 00:0d: iomem range 0xe0000000-0xefffffff has been reserved
pnp: 00:0e: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0e: iomem range 0xc0000-0xcffff could not be reserved
pnp: 00:0e: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0e: iomem range 0x100000-0x1fffffff could not be reserved
ieee1394: Initialized config rom entry `ip1394'
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:02.0
IO window: c000-cfff
MEM window: 9fd00000-dfdfffff
PREFETCH window: 30000000-3fffffff
PCI: Bridge: 0000:00:19.0
IO window: d000-dfff
MEM window: dfe00000-dfefffff
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:02.0 to 64
PCI: Setting latency timer of device 0000:00:19.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 196608 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NTFS driver 2.1.28 [Flags: R/O].
JFS: nTxBlock = 3985, nTxLock = 31883
SGI XFS with ACLs, security attributes, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
OCFS2 1.3.3
OCFS2 Node Manager 1.3.3
OCFS2 DLM 1.3.3
OCFS2 DLMFS 1.3.3
OCFS2 User DLM kernel interface loaded
GFS2 (built Aug 25 2007 18:53:39) installed
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0cie00]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
vesafb: framebuffer at 0xb1000000, mapped to 0xe0a80000, using 3072k, total 14336k
vesafb: mode is 1024x768x8, linelength=1024, pages=3
vesafb: protected mode interface info at c000:b420
vesafb: pmi: set display start = c00cb483, set palette = c00cb4de
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da

[snake eyes]

dmesg contd....

vesafb: scrolling: redraw
vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
ACPI: Processor [CPU1] (supports 8 throttling states)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: module loaded
Compaq SMART2 Driver (v 2.6.0)
HP CISS Driver (v 3.6.14)
input: Macintosh mouse button emulation as /class/input/input2
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 0000:00:1f.0
ACPI: PCI Interrupt 0000:00:1f.0[A] -> GSI 21 (level, low) -> IRQ 16
ALI15X3: chipset revision 199
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hdaio, hdbMA
ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdcio, hddMA
Probing IDE interface ide0...
hdb: SONY CD-RW CRX320EE, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdd: ST320413A, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hdd: max request size: 128KiB
hdd: 39102336 sectors (20020 MB) w/512KiB Cache, CHS=38792/16/63, UDMA(100)
hdd: cache flushes not supported
hdd: hdd1
hdb: ATAPI 52X DVD-ROM CD-R/RW drive, 1536kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
Loading iSCSI transport class v2.0-724.
iscsi: registered transport (tcp)
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
Adaptec aacraid driver (1.1-5[2423]-mh3)
aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
scsi: <fdomain> Detection failed (no card)
sym53c416.c: Version 1.0.0-ac
qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options<6>QLogic Fibre Channel HBA Driver
iscsi: registered transport (qla4xxx)
QLogic iSCSI HBA Driver
Emulex LightPulse Fibre Channel SCSI driver 8.1.11
Copyright(c) 2004-2006 Emulex. All rights reserved.
seagate: ST0x/TMC-8xx not detected.
Failed initialization of WD-7000 SCSI card!
DC390: clustering now enabled by default. If you get problems load
with "disable_clustering=1" and report to maintainers
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.03.10-rc1 Wed Feb 14 10:14:25 PST 2007
GDT-HA: Storage RAID Controller Driver. Version: 3.05
GDT-HA: Found 0 PCI Storage RAID Controllers
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.008.
nsp32: loading...
ipr: IBM Power RAID SCSI Device Driver version: 2.3.1 (January 23, 2007)
RocketRAID 3xxx SATA Controller driver v1.0 (060426)
st: Version 20070203, fixed bufsize 32768, s/g segs 256
sata_uli 0000:00:1f.1: version 1.1
PCI: Enabling device 0000:00:1f.1 (0105 -> 0107)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 21 (level, low) -> IRQ 16
ata1: SATA max UDMA/133 cmd 0x0001ec00 ctl 0x0001e882 bmdma 0x0001e400 irq 16
ata2: SATA max UDMA/133 cmd 0x0001e800 ctl 0x0001e482 bmdma 0x0001e408 irq 16
ata3: SATA max UDMA/133 cmd 0x0001ec08 ctl 0x0001e886 bmdma 0x0001e410 irq 16
ata4: SATA max UDMA/133 cmd 0x0001e808 ctl 0x0001e486 bmdma 0x0001e418 irq 16
scsi2 : sata_uli
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: WDC WD1600AABS-00PRA0, 05.06H05, max UDMA/133
ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi3 : sata_uli
ata2: SATA link down (SStatus 0 SControl 300)
scsi4 : sata_uli
ata3: SATA link down (SStatus 0 SControl 300)
scsi5 : sata_uli
ata4: SATA link down (SStatus 0 SControl 300)
scsi 2:0:0:0: Direct-Access ATA WDC WD1600AABS-0 05.0 PQ: 0 ANSI: 5
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: disabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda3 < sda5 sda6 sda7 sda8 > sda4
sd 2:0:0:0: Attached scsi disk sda
I2O subsystem v1.325
i2o: max drivers = 8
I2O Configuration OSM v1.323
I2O Bus Adapter OSM v1.317
I2O Block Device OSM v1.325
I2O SCSI Peripheral OSM v1.316
I2O ProcFS OSM v1.316
Fusion MPT base driver 3.04.04
Copyright (c) 1999-2007 LSI Logic Corporation
Fusion MPT SPI Host driver 3.04.04
Fusion MPT FC Host driver 3.04.04
Fusion MPT SAS Host driver 3.04.04
usbmon: debugfs is not available
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 23 (level, low) -> IRQ 17
ehci_hcd 0000:00:1c.3: EHCI Host Controller
ehci_hcd 0000:00:1c.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1c.3: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1c.3
ehci_hcd 0000:00:1c.3: irq 17, io mem 0xdffff800
ehci_hcd 0000:00:1c.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
116x: driver isp116x-hcd, 03 Nov 2005
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 18
ohci_hcd 0000:00:1c.0: OHCI Host Controller
ohci_hcd 0000:00:1c.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:1c.0: irq 18, io mem 0xdfffc000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 18 (level, low) -> IRQ 19
ohci_hcd 0000:00:1c.1: OHCI Host Controller
ohci_hcd 0000:00:1c.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:1c.1: irq 19, io mem 0xdfffd000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 19 (level, low) -> IRQ 20
ohci_hcd 0000:00:1c.2: OHCI Host Controller
ohci_hcd 0000:00:1c.2: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:1c.2: irq 20, io mem 0xdfffe000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 3 ports detected
USB Universal Host Controller Interface driver v3.0
sl811: driver sl811-hcd, 19 May 2005
Initializing USB Mass Storage driver...
usb 3-1: new full speed USB device using ohci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
raid6: int32x1 768 MB/s
raid6: int32x2 754 MB/s
raid6: int32x4 631 MB/s
raid6: int32x8 500 MB/s
raid6: mmxx1 1663 MB/s
raid6: mmxx2 1947 MB/s
raid6: sse1x1 972 MB/s
raid6: sse1x2 1902 MB/s
raid6: sse2x1 1973 MB/s
raid6: sse2x2 2996 MB/s
raid6: using algorithm sse2x2 (2996 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: automatically using best checksumming function: pIII_sse
pIII_sse : 4379.000 MB/sec
raid5: using function: pIII_sse (4379.000 MB/sec)
md: multipath personality registered for level -4
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
input: AT Translated Set 2 keyboard as /class/input/input3
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
ReiserFS: sda5: found reiserfs format "3.6" with standard journal
ReiserFS: sda5: using ordered data mode
ReiserFS: sda5: journal params: device sda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30

[snake eyes]

dmesg ..ends...

ReiserFS: sda5: checking transaction log (sda5)
ReiserFS: sda5: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 388k freed
sd 2:0:0:0: Attached scsi generic sg0 type 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Linux agpgart interface v0.102 (c) Dave Jones
ali15x3_smbus 0000:00:1e.1: ALI15X3_smb region uninitialized - upgrade BIOS or use force_addr=0xaddr
ali15x3_smbus 0000:00:1e.1: ALI15X3 not detected, module not inserted.
ali1535_smbus 0000:00:1e.1: ALI1535_smb region uninitialized - upgrade BIOS?
ali1535_smbus 0000:00:1e.1: ALI1535 not detected, module not inserted.
alim7101_wdt: Steve Hill <steve@navaho.co.uk>.
alim7101_wdt: ALi 1543 South-Bridge not present - WDT not set
ACPI: PCI Interrupt 0000:00:1d.0[C] -> GSI 22 (level, low) -> IRQ 21
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: HCI USB driver ver 2.9
usbcore: registered new interface driver hci_usb
hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdd: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdd: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdd: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdd: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdd: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdd: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
ide1: reset: master: error (0x00?)
Adding 530104k swap on /dev/sda6. Priority:-1 extents:1 across:530104k
input: PC Speaker as /class/input/input4
input: ImPS/2 Generic Wheel Mouse as /class/input/input5
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
lp0: console ready
fuse init (API version 7.8)
Capability LSM initialized
Intel ISA PCIC probe: not found.
Databook TCIC-2 PCMCIA probe: not found.