Results 1 to 6 of 6

Thread: problem with rtl8187se recon

Threaded View

  1. #1
    Just burned their ISO
    Join Date
    Nov 2012
    Posts
    4

    Default problem with rtl8187se recon

    im booting bt5 r2 frm usb in my toshiba protege T110 laptop. it use to be working all well
    until recently i tried using metaspoilt & run an update on it. now it doesnt scan the wireless
    network like it used to be, behaving unusual. However, when i ran the bt5 usb on different laptop,it works fine. so the problem is not the usb live distro for sure.
    here is few command that i ran to chk, pls go thru the info & try figure out what is wrong with my wireless card or setting in bt5 was changed.

    i hv tried ifconfig wlan0 up, iwconfig wlan0 start, /etc/init.d/wicd start, /etc/init.d/networking start & few more that I can find frm some forum but doesn't solve the issue.
    Below are the respond I got:-

    ifconfig

    wlan0 Link encap:UNSPEC HWaddr 00-26-B6-32-34-01-30-30-00-00-00-00-00-00-00-00
    UP BROADCAST NOTRAILERS RUNNING PROMISC ALLMULTI MTU:1500 Metric:1
    RX packets:293 errors:2 dropped:0 overruns:0 frame:0
    TX packets:428 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:34695 (34.6 KB) TX bytes:17976 (17.9 KB)
    Interrupt:17 Memory:f87f0000-f87f0100


    iwconfig

    wlan0 802.11b/g Mode:Monitor Frequency=2.447 GHz Bit Rate=11 Mb/s
    Retryn RTS thrff Fragment thrff
    Power Managementff
    Link Quality=0/100 Signal level=0 dBm Noise level=0 dBm
    Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
    Tx excessive retries:0 Invalid misc:0 Missed beacon:0

    airodump-ng start wlan0

    CH 4 ][ BAT: 1 hour 56 mins ][ Elapsed: 4 mins ][ 2012-11-21 01:24

    BSSID PWR Beacons #Data, #/s CH MB ENC CIPHER AUTH ESSID


    BSSID STATION PWR Rate Lost Frames Probe

    Only when i activate Wicd Network Manager then it start scanning & displaying wireless network? However, notice the PWR column doesn't show any indication which usually does!!!
    This scan only last for less than 3 minutes then all wireless gone missing again. As if the wireless card wasn't scanning at all.

    CH 6 ][ BAT: 1 hour 55 mins ][ Elapsed: 24 s ][ 2012-11-21 01:17

    BSSID PWR Beacons #Data, #/s CH MB ENC CIPHER AUTH ESSID

    00:25:3C:BB:9B:79 0 6 2 0 6 54 . WPA2 CCMP PSK 2WIRE663
    00:25:3C:77:C6:51 0 4 2 0 10 54 . WPA2 CCMP PSK MAZEHOME

    BSSID STATION PWR Rate Lost Frames Probe

    00:25:3C:BB:9B:79 20:64:32:21:EE:46 0 0 - 0 0 2
    00:25:3C:77:C6:51 00:1F:1F:4B:36:5A -1 0 - 0 0 1
    00:25:3C:77:C6:51 5C:0A:5B:13:63:E1 -1 0 - 0 0 1

    Below is the dmesg output:



    19.445152] r8187se: module is from the staging directory, the quality is unknown, you have been warned.
    [ 19.518227] Linux video capture interface: v2.00
    [ 19.543254] ieee80211_crypt: registered algorithm 'NULL'
    [ 19.543260] ieee80211_crypt: registered algorithm 'TKIP'
    [ 19.543263] ieee80211_crypt: registered algorithm 'CCMP'
    [ 19.543266] ieee80211_crypt: registered algorithm 'WEP'
    [ 19.543268]
    [ 19.543270] Linux kernel driver for RTL8180 / RTL8185 based WLAN cards
    [ 19.543272] Copyright (c) 2004-2005, Andrea Merello
    [ 19.543275] r8180: Initializing module
    [ 19.543278] r8180: Wireless extensions version 22
    [ 19.543280] r8180: Initializing proc filesystem
    [ 19.543317] r8180: Configuring chip resources
    [ 19.543330] r8180 0000:08:00.0: enabling device (0000 -> 0003)
    [ 19.543343] r8180 0000:08:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    [ 19.543355] r8180 0000:08:00.0: setting latency timer to 64
    [ 19.580466] rtl8180_init:Error channel plan! Set to default.
    [ 19.580471] r8180: Channel plan is 0
    [ 19.580473]
    [ 19.580475] Dot11d_Init()
    [ 19.580479] r8180: MAC controller is a RTL8187SE b/g
    [ 19.582635] r8180: usValue is 0x104
    [ 19.582637]
    [ 19.625808] r8180: EEPROM version 104
    [ 19.630130] r8180: WW:**PLEASE** REPORT SUCCESSFUL/UNSUCCESSFUL TO Realtek!
    [ 19.678531] r8180: IRQ 17
    [ 19.679600] Registered led device: toshiba::illumination
    [ 19.687387] r8180: Driver probe completed
    [ 19.687389]


    at this point im connected to my own wireless network

    [ 112.208530] r8180: Bringing up iface
    [ 112.407016] r8180: Card successfully reset
    [ 113.146584] r8180: WIRELESS_MODE_G
    [ 113.146586]
    [ 113.164079] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 113.244323] atl1c 0000:07:00.0: irq 45 for MSI/MSI-X
    [ 113.304687] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 113.384898] r8180: Bringing up iface
    [ 113.583383] r8180: Card successfully reset
    [ 114.322926] r8180: WIRELESS_MODE_G
    [ 114.322928]
    [ 114.355519] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 116.579096] Linking with 2WIRE663: channel is 6
    [ 116.624011] Linking with 2WIRE663: channel is 6
    [ 116.664704] Linking with 2WIRE663: channel is 6
    [ 116.682293] Associated successfully
    [ 116.682298] Using G rates
    [ 116.696527] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
    [ 119.739117] Associated successfully
    [ 119.739122] Using G rates
    [ 122.796149] Associated successfully
    [ 122.796155] Using G rates
    [ 125.859603] Associated successfully
    [ 125.859608] Using G rates
    [ 126.768075] wlan0: no IPv6 routers present
    [ 128.918212] Associated successfully
    [ 128.918217] Using G rates
    [ 131.977071] Associated successfully
    [ 131.977077] Using G rates
    [ 135.034097] Associated successfully
    [ 135.034102] Using G rates
    [ 138.083447] Associated successfully
    [ 138.083453] Using G rates
    [ 141.137171] Associated successfully
    [ 141.137176] Using G rates
    [ 144.201680] Associated successfully
    [ 144.201686] Using G rates
    [ 147.246437] Associated successfully
    [ 147.246443] Using G rates
    [ 150.295484] Associated successfully
    [ 150.295490] Using G rates
    [ 152.005151] r8180: Bringing up iface
    [ 152.203636] r8180: Card successfully reset
    [ 152.943144] r8180: WIRELESS_MODE_G
    [ 152.943146]
    [ 152.980658] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 153.136860] atl1c 0000:07:00.0: irq 45 for MSI/MSI-X
    [ 153.196648] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 217.861644] r8180: Bringing up iface
    [ 218.060133] r8180: Card successfully reset
    [ 218.799783] r8180: WIRELESS_MODE_G
    [ 218.799784]
    [ 218.830985] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 218.871183] r8180: Bringing up iface
    [ 219.069676] r8180: Card successfully reset
    [ 219.809369] r8180: WIRELESS_MODE_G
    [ 219.809371]
    [ 219.826345] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 219.895633] atl1c 0000:07:00.0: irq 45 for MSI/MSI-X
    [ 219.952676] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 220.060704] r8180: Bringing up iface
    [ 220.259215] r8180: Card successfully reset
    [ 220.998865] r8180: WIRELESS_MODE_G
    [ 220.998867]
    [ 221.029617] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 223.206673] Linking with 2WIRE663: channel is 6
    [ 223.247514] Linking with 2WIRE663: channel is 6
    [ 223.265837] Associated successfully
    [ 223.265842] Using G rates
    [ 223.281592] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
    [ 223.308765] Linking with 2WIRE663: channel is 6
    [ 223.327004] Associated successfully
    [ 223.327008] Using G rates
    [ 233.712096] wlan0: no IPv6 routers present
    [ 1391.071176] r8180: Bringing up iface
    [ 1391.269696] r8180: Card successfully reset
    [ 1392.009249] r8180: WIRELESS_MODE_G
    [ 1392.009251]
    [ 1392.039899] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 1392.199317] atl1c 0000:07:00.0: irq 45 for MSI/MSI-X
    [ 1392.256653] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 1392.432906] r8180: Bringing up iface
    [ 1392.631391] r8180: Card successfully reset
    [ 1393.370904] r8180: WIRELESS_MODE_G
    [ 1393.370906]
    [ 1393.403993] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 1393.506593] r8180: Bringing up iface
    [ 1393.705080] r8180: Card successfully reset
    [ 1394.444589] r8180: WIRELESS_MODE_G
    [ 1394.444591]
    [ 1394.466302] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 1394.563660] atl1c 0000:07:00.0: irq 45 for MSI/MSI-X
    [ 1394.620782] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 1396.352173] PM: Syncing filesystems ... done.
    [ 1396.352199] Freezing user space processes ... (elapsed 0.01 seconds) done.
    [ 1396.368048] Freezing remaining freezable tasks ... (elapsed 0.01 seconds)




    can some expert in linux here help to solve my issue. appreciate your great HELP.
    Last edited by confussed; 03-04-2013 at 05:33 AM. Reason: additional info

Similar Threads

  1. Creating Wireless Recon Maps
    By masry in forum BackTrack 5 Beginners Section
    Replies: 3
    Last Post: 11-30-2011, 12:55 PM
  2. Uberharvest 2.54 recon tool (Updated)
    By Yakov in forum BackTrack 5 Tool Requests (NOW CLOSED) Please see sticky
    Replies: 0
    Last Post: 09-12-2011, 05:36 PM
  3. uberharvest, for website recon.
    By Sys7emR00t in forum BackTrack 5 Tool Requests (NOW CLOSED) Please see sticky
    Replies: 1
    Last Post: 09-12-2011, 05:33 PM
  4. rtl8187se
    By malam in forum Angolo Wireless
    Replies: 3
    Last Post: 07-18-2009, 11:11 AM
  5. rtl8187se in backtrack 4
    By cain#1 in forum OLD Newbie Area
    Replies: 1
    Last Post: 06-05-2009, 05:57 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •