Is this the classic trying to use on-board wireless module inside a VM?
Just to make it clear, are you using BT in Virtual Machine with a USB wifi adapter of some sort?
Hi guys,
i want ask, how to solve error during install wifi driver. and how to fix it ?
speck acer aspire 5536, chipset wif is atheros ar5b91 (installed win 7 32 as host, and baktrack 5 r3 gnome via wm)
message after installed like this
root@bt:~/madwifi-0.9.4# su
root@bt:~/madwifi-0.9.4# make install
sh scripts/find-madwifi-modules.sh 3.2.6
for i in ath/ ath_hal/ ath_rate/ net80211/; do \
make -C $i install || exit 1; \
done
make[1]: Entering directory `/root/madwifi-0.9.4/ath'
test -d //lib/modules/3.2.6/net || mkdir -p //lib/modules/3.2.6/net
install ath_pci.ko //lib/modules/3.2.6/net
install: cannot stat `ath_pci.ko': No such file or directory
make[1]: *** [install] Error 1
make[1]: Leaving directory `/root/madwifi-0.9.4/ath'
make: *** [install-modules] Error 1
root@bt:~/madwifi-0.9.4# modprobe ath_pci
FATAL: Module ath_pci not found.
root@bt:~/madwifi-0.9.4#
Can you help me fix it & works fine ?
thanks in advance
Is this the classic trying to use on-board wireless module inside a VM?
Just to make it clear, are you using BT in Virtual Machine with a USB wifi adapter of some sort?
yes I've set in the vm and bt, but the drivers wifi have not been successful installation! how turn it on and instructions please?
below is ss of installation & virtual network editor + set it on bt
root@bt:~# cd madwifi-0.9.4
root@bt:~/madwifi-0.9.4# make
Checking requirements... ok.
Checking kernel configuration... FAILED
Only kernel versions 2.4.x and above are supported.
You have 3.2.6.
make: *** [configcheck] Error 1
root@bt:~/madwifi-0.9.4# make install
sh scripts/find-madwifi-modules.sh 3.2.6
for i in ath/ ath_hal/ ath_rate/ net80211/; do \
make -C $i install || exit 1; \
done
make[1]: Entering directory `/root/madwifi-0.9.4/ath'
test -d //lib/modules/3.2.6/net || mkdir -p //lib/modules/3.2.6/net
install ath_pci.ko //lib/modules/3.2.6/net
install: cannot stat `ath_pci.ko': No such file or directory
make[1]: *** [install] Error 1
make[1]: Leaving directory `/root/madwifi-0.9.4/ath'
make: *** [install-modules] Error 1
root@bt:~/madwifi-0.9.4# modprobe ath_pci
FATAL: Module ath_pci not found.
root@bt:~/madwifi-0.9.4# ifconfig
eth0 Link encap:Ethernet HWaddr 00:0c:29:79:1f:9a
inet6 addr: fe80::20c:29ff:fe79:1f9a/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:5164 errors:0 dropped:0 overruns:0 frame:0
TX packets:4909 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:6051959 (6.0 MB) TX bytes:303420 (303.4 KB)
Interrupt:19 Base address:0x2024
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:94 errors:0 dropped:0 overruns:0 frame:0
TX packets:94 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:6625 (6.6 KB) TX bytes:6625 (6.6 KB)
root@bt:~/madwifi-0.9.4#
confused ,,,,
I don't use usb adapter wifi right now, but after this successfuly, I plan to use tp link TL-WN722N !
thank you
He (jimmy87) is trying to tell you that VM cannot use Internal or on-board pci, pci-e, mini pci-e or any internal wifi card.
Sorry, you need a USB device, "finale", period, punto, etc..Do not waste your time my friend.
One piece of advice: Before buying a USB wifi device, please, check which ones are 100% operational in BT5 (Some devices running under VM have issues, but in DVD live or HDD installations run perfectly).
Refer to the forums or ask about them...
Luck.
you're welcome, & my friend