Integrated WiFi card Problem (Backtrack doesn't detect it[Acer Nplify 802.11b/g/n])
Introduction:
Hello, I have a big problem. System doesn't detect WiFi card. I tried a lot of metods, but they were useless. Please help me.
Details:
I use BackTrack 5 r3 GNOME 32bit installed from USB.
I'm currently connected with cable :S
Here is the output of some basic commands:
iwconfig:
ifconfig:Code:root@bt:~# iwconfig lo no wireless extensions. eth0 no wireless extensions.
lspci:Code:root@bt:~# ifconfig eth0 Link encap:Ethernet HWaddr dc:0e:a1:9b:1f:0d inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::de0e:a1ff:fe9b:1f0d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:80764 errors:0 dropped:0 overruns:0 frame:0 TX packets:50922 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:105283787 (105.2 MB) TX bytes:7389118 (7.3 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:519 errors:0 dropped:0 overruns:0 frame:0 TX packets:519 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:150621 (150.6 KB) TX bytes:150621 (150.6 KB)
airmon-ng:Code:root@bt:~# lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b4) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b4) 00:1d.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 04) 01:00.0 VGA compatible controller: nVidia Corporation Device 0de9 (rev a1) 02:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57785 Gigabit Ethernet PCIe (rev 10) 02:00.1 SD Host controller: Broadcom Corporation NetXtreme BCM57765 Memory Card Reader (rev 10) 02:00.2 System peripheral: Broadcom Corporation Device 16be (rev 10) 02:00.3 System peripheral: Broadcom Corporation Device 16bf (rev 10) 03:00.0 Network controller: Broadcom Corporation BCM43227 802.11b/g/n
airodump-ng:Code:root@bt:~# airmon-ng Interface Chipset Driver
dmesg | tail:Code:root@bt:~# airodump-ng Airodump-ng 1.1 r2178 - (C) 2006-2010 Thomas d'Otreppe Original work: Christophe Devine http://www.aircrack-ng.org usage: airodump-ng <options> <interface>[,<interface>,...] Options: --ivs : Save only captured IVs --gpsd : Use GPSd --write <prefix> : Dump file prefix -w : same as --write --beacons : Record all beacons in dump file --update <secs> : Display update delay in seconds --showack : Prints ack/cts/rts statistics -h : Hides known stations for --showack -f <msecs> : Time in ms between hopping channels --berlin <secs> : Time before removing the AP/client from the screen when no more packets are received (Default: 120 seconds) -r <file> : Read packets from that file -x <msecs> : Active Scanning Simulation --output-format <formats> : Output format. Possible values: pcap, ivs, csv, gps, kismet, netxml --ignore-negative-one : Removes the message that says fixed channel <interface>: -1 Filter options: --encrypt <suite> : Filter APs by cipher suite --netmask <netmask> : Filter APs by mask --bssid <bssid> : Filter APs by BSSID -a : Filter unassociated clients By default, airodump-ng hop on 2.4GHz channels. You can make it capture on other/specific channel(s) by using: --channel <channels> : Capture on specific channels --band <abg> : Band on which airodump-ng should hop -C <frequencies> : Uses these frequencies in MHz to hop --cswitch <method> : Set channel switching method 0 : FIFO (default) 1 : Round Robin 2 : Hop on last -s : same as --cswitch --help : Displays this usage screen No interface specified.
Code:root@bt:~# dmesg | tail [ 80.306669] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 80.623255] tg3 0000:02:00.0: irq 44 for MSI/MSI-X [ 80.623260] tg3 0000:02:00.0: irq 45 for MSI/MSI-X [ 80.623264] tg3 0000:02:00.0: irq 46 for MSI/MSI-X [ 80.786354] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 82.369877] tg3 0000:02:00.0: eth0: Link is up at 100 Mbps, full duplex [ 82.369881] tg3 0000:02:00.0: eth0: Flow control is on for TX and on for RX [ 82.369883] tg3 0000:02:00.0: eth0: EEE is disabled [ 82.369999] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 92.497997] eth0: no IPv6 routers present
I also tried with Network Manager but it's same,no wireless found.
