Page 2 of 6 FirstFirst 1234 ... LastLast
Results 11 to 20 of 54

Thread: Intel integrated graphics are not working

  1. #11
    Just burned their ISO
    Join Date
    Jan 2013
    Posts
    19

    Default Re: Intel integrated graphics are not working-dmesg o/p

    Quote Originally Posted by maverik35 View Post
    Again, I do not see the driver loaded, try loading it manually: modprobe i915 modeset=1
    See if it is loaded by retyping lspci -vvs xx:xx.x

    Please would you post the dmesg output?
    and the other dmesg output which you asked:


    output of dmesg after modprobe:
    0.000009] pid_max: default: 32768 minimum: 301
    [ 0.000029] Security Framework initialized
    [ 0.000041] AppArmor: AppArmor initialized
    [ 0.000078] Mount-cache hash table entries: 512
    [ 0.000179] Initializing cgroup subsys cpuacct
    [ 0.000185] Initializing cgroup subsys memory
    [ 0.000192] Initializing cgroup subsys devices
    [ 0.000195] Initializing cgroup subsys freezer
    [ 0.000198] Initializing cgroup subsys net_cls
    [ 0.000201] Initializing cgroup subsys blkio
    [ 0.000206] Initializing cgroup subsys perf_event
    [ 0.000228] CPU: Physical Processor ID: 0
    [ 0.000231] CPU: Processor Core ID: 0
    [ 0.000237] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
    [ 0.000238] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
    [ 0.000244] mce: CPU supports 7 MCE banks
    [ 0.000257] CPU0: Thermal monitoring enabled (TM1)
    [ 0.000264] using mwait in idle threads.
    [ 0.002483] ACPI: Core revision 20110623
    [ 0.008809] ftrace: allocating 22920 entries in 45 pages
    [ 0.016489] Enabling APIC mode: Flat. Using 1 I/O APICs
    [ 0.016912] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.056532] CPU0: Intel(R) Core(TM) i3-3110M CPU @ 2.40GHz stepping 09
    [ 0.163921] Performance Events: PEBS fmt1+, generic architected perfmon, Intel PMU driver.
    [ 0.163929] ... version: 3
    [ 0.163932] ... bit width: 48
    [ 0.163934] ... generic registers: 4
    [ 0.163937] ... value mask: 0000ffffffffffff
    [ 0.163940] ... max period: 000000007fffffff
    [ 0.163943] ... fixed-purpose events: 3
    [ 0.163945] ... event mask: 000000070000000f
    [ 0.164084] NMI watchdog enabled, takes one hw-pmu counter.
    [ 0.164151] CPU 1 irqstacks, hard=f5960000 soft=f5962000
    [ 0.164153] Booting Node 0, Processors #1
    [ 0.164156] smpboot cpu 1: start_ip = 99000
    [ 0.174515] Initializing CPU#1
    [ 0.271834] NMI watchdog enabled, takes one hw-pmu counter.
    [ 0.271904] CPU 2 irqstacks, hard=f596e000 soft=f5970000
    [ 0.271906] #2
    [ 0.271907] smpboot cpu 2: start_ip = 99000
    [ 0.282141] Initializing CPU#2
    [ 0.379717] NMI watchdog enabled, takes one hw-pmu counter.
    [ 0.379783] CPU 3 irqstacks, hard=f5984000 soft=f5986000
    [ 0.379785] #3
    [ 0.379786] smpboot cpu 3: start_ip = 99000
    [ 0.390019] Initializing CPU#3
    [ 0.487498] NMI watchdog enabled, takes one hw-pmu counter.
    [ 0.487526] Brought up 4 CPUs
    [ 0.487529] Total of 4 processors activated (19155.65 BogoMIPS).
    [ 0.490970] devtmpfs: initialized
    [ 0.491055] EVM: security.selinux
    [ 0.491057] EVM: security.SMACK64
    [ 0.491060] EVM: security.capability
    [ 0.491080] PM: Registering ACPI NVS region at 79eef000 (720896 bytes)
    [ 0.491868] print_constraints: dummy:
    [ 1.062177] ERST: Table is not found!
    [ 1.062203] GHES: HEST is not enabled!
    [ 1.062237] isapnp: Scanning for PnP cards...
    [ 1.067042] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
    [ 1.067092] ACPI: Battery Slot [BAT1] (battery present)
    [ 1.415789] isapnp: No Plug & Play device found
    [ 1.416850] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
    [ 1.457357] Linux agpgart interface v0.103
    [ 1.458439] agpgart-intel 0000:00:00.0: Intel Ivybridge Chipset
    [ 1.459520] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
    [ 1.461437] agpgart-intel 0000:00:00.0: detected 65536K stolen memory
    [ 1.462565] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x80000000
    [ 1.464592] brd: module loaded
    [ 1.466132] loop: module loaded
    [ 1.467196] ahci 0000:00:1f.2: version 3.0
    [ 1.467208] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
    [ 1.468272] ahci 0000:00:1f.2: irq 40 for MSI/MSI-X
    [ 1.480947] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 3 Gbps 0x5 impl SATA mode
    [ 1.481980] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part ems apst
    [ 1.483008] ahci 0000:00:1f.2: setting latency timer to 64
    [
    [ 1.501716] Fixed MDIO Bus: probed
    [ 1.502676] tun: Universal TUN/TAP device driver, 1.6
    [ 1.503610] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
    [ 1.504576] arcnet loaded.
    [ 1.505496] PPP generic driver version 2.4.2
    [ 1.506471] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 1.529854] hub 1-0:1.0: USB hub found
    [ 1.530781] hub 1-0:1.0: 3 ports detected
    [ 1.531756] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
    [ 1.532710] ehci_hcd 0000:00:1d.0: setting latency timer to 64
    [ 1.532713] ehci_hcd 0000:00:1d.0: EHCI Host Controller
    [ 1.533689] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
    [ 1.534658] ehci_hcd 0000:00:1d.0: debug port 2
    [ 1.539484] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
    [ 1.539496] ehci_hcd 0000:00:1d.0: irq 23, io mem 0x90609000
    [ 1.552827] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
    [ 1.553838] hub 2-0:1.0: USB hub found
    [ 1.554780] hub 2-0:1.0: 3 ports detected
    [ 1.555731] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    [ 1.556645] uhci_hcd: USB Universal Host Controller Interface driver
    [ 1.557625] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:EPAD] at 0x60,0x64 irq 1,12
    [ 1.562142] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 1.563060] serio: i8042 AUX port at 0x60,0x64 irq 12
    [ 1.564036] mousedev: PS/2 mouse device common for all mice
    [ 1.565201] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
    [ 1.566141] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
    [ 1.567107] device-mapper: uevent: version 1.0.3
    [ 1.568077] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
    [ 1.569054] EISA: Probing bus 0 at eisa.0
    [ 1.569982] EISA: Cannot allocate resource for mainboard
    [ 1.578155] EISA: Detected 0 cards.
    [ 1.579027] cpufreq-nforce2: No nForce2 chipset.
    [ 1.579954] cpuidle: using governor ladder
    [ 1.580924] cpuidle: using governor menu
    [ 1.581763] EFI Variables Facility v0.08 2004-May-17
    [ 1.582749] TCP cubic registered
    [ 1.583686] NET: Registered protocol family 10
    [ 1.584874] NET: Registered protocol family 17
    [ 1.585724] Registering the dns_resolver key type
    [ 1.586588] Using IPI No-Shortcut mode
    [ 1.587529] registered taskstats version 1
    [ 1.596061] rtc_cmos 00:06: setting system clock to 2013-02-06 20:26:03 UTC (1360182363)
    [ 1.597515] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
    [ 1.598372] EDD information not available.
    [ 1.599328] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
    [ 2.217729] hub 2-1:1.0: 6 ports detected
    [ 2.291921] usb 1-1.4: new high-speed USB device number 3 using ehci_hcd
    [ 2.575452] usb 2-1.3: new high-speed USB device number 3 using ehci_hcd
    [ 2.670834] usbcore: registered new interface driver uas
    [ 2.672429] Initializing USB Mass Storage driver...
    [ 2.673635] scsi6 : usb-storage 2-1.3:1.0
    [ 2.674811] usbcore: registered new interface driver usb-storage
    [ 2.675934] USB Mass Storage support registered.
    [ 2.743216] usb 2-1.4: new full-speed USB device number 4 using ehci_hcd
    [ 3.670479] scsi 6:0:0:0: Direct-Access Multiple Card Reader 1.00 PQ: 0 ANSI: 0
    [ 3.672206] sd 6:0:0:0: Attached scsi generic sg2 type 0
    [ 3.921567] sd 6:0:0:0: [sdb] Attached SCSI removable disk
    [ 4.108080] aufs 3.2-20120109
    [ 4.357798] EXT4-fs (sda9): mounted filesystem with ordered data mode. Opts: (null)
    [ 6.295643] Adding 1998844k swap on /dev/sda7. Priority:-1 extents:1 across:1998844k
    [ 6.339257] udev: starting version 151
    [ 7.123789] cfg80211: Calling CRDA to update world regulatory domain
    [ 7.294799] Bluetooth: Core ver 2.16
    [ 7.359108] Linux video capture interface: v2.00
    [ 7.382282] uvcvideo: Found UVC 1.00 device WebCam SC-13HDL11939N (2232:1029)
    [ 7.393086] input: WebCam SC-13HDL11939N as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.4/1-1.4:1.0/input/input4
    [ 7.393193] usbcore: registered new interface driver uvcvideo
    [ 7.393196] USB Video Class driver (1.1.1)
    [ 7.434652] psmouse serio1: hgpk: ID: 10 00 64
    [ 7.520992] mei: module is from the staging directory, the quality is unknown, you have been warned.
    [ 7.521208] mei 0000:00:16.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [ 7.521214] mei 0000:00:16.0: setting latency timer to 64
    [ 7.521262] mei 0000:00:16.0: irq 42 for MSI/MSI-X
    [
    [ 8.376645] lp: driver loaded but no devices found
    [ 8.404460] ieee80211 phy0: Selected rate control algorithm 'ath9k_rate_control'
    [ 8.404890] Registered led device: ath9k-phy0
    [ 8.404899] ieee80211 phy0: Atheros AR9485 Rev:1 mem=0xf8b00000, irq=16
    [ 9.386019] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
    [ 9.386071] snd_hda_intel 0000:00:1b.0: irq 43 for MSI/MSI-X
    [ 9.386098] snd_hda_intel 0000:00:1b.0: setting latency timer to 64

  2. #12
    Very good friend of the forum maverik35's Avatar
    Join Date
    Sep 2009
    Location
    Debian land
    Posts
    734

    Default Re: Intel integrated graphics are not working

    Quote Originally Posted by zigmos View Post
    i executed the modprobe command at terminal and my desktop screen got shifted to right by 3 inch approx.Although it got restored back as earlier after reboot.
    Output of lspci -vvs after modprobe :


    sudo lspci -vvs 00:02.0
    00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)
    Subsystem: Samsung Electronics Co Ltd Device c652
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 11
    Region 0: Memory at 90000000 (64-bit, non-prefetchable) [size=4M]
    Region 2: Memory at 80000000 (64-bit, prefetchable) [size=256M]
    Region 4: I/O ports at 3000 [size=64]
    Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
    Address: 00000000 Data: 0000
    Capabilities: [d0] Power Management version 2
    Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [a4] PCIe advanced features <?>
    That is quiet interesting..You say it shifted about 3", but still it does not show it in lspci....Try again , but now without modeset = 1, just i915....

  3. #13
    Just burned their ISO
    Join Date
    Dec 2012
    Location
    where I'm needed
    Posts
    20

    Default Re: Intel integrated graphics are not working

    Quote Originally Posted by zigmos View Post
    i executed the modprobe command at terminal and my desktop screen got shifted to right by 3 inch approx.Although it got restored back as earlier after reboot.
    I cant deduce exactly from what you wrote above, therefore I must say: you must make sure that when you issue "modprobe i915 modeset=1" command, you are completely in text mode (aka command line mode). This means, you call modeprobe cmd BEFORE you issue the startx command!
    Even if your screen gets shifted, try to do "startx" blindfold and see if the resolution gets fixed.

    Output of lspci -vvs after modprobe :


    sudo lspci -vvs 00:02.0
    00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)
    Subsystem: Samsung Electronics Co Ltd Device c652
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 11
    Region 0: Memory at 90000000 (64-bit, non-prefetchable) [size=4M]
    Region 2: Memory at 80000000 (64-bit, prefetchable) [size=256M]
    Region 4: I/O ports at 3000 [size=64]
    Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
    Address: 00000000 Data: 0000
    Capabilities: [d0] Power Management version 2
    Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [a4] PCIe advanced features <?>
    This definetly means that your graphic card is NOT using the i915 kernel driver.

  4. #14
    Very good friend of the forum maverik35's Avatar
    Join Date
    Sep 2009
    Location
    Debian land
    Posts
    734

    Default Re: Intel integrated graphics are not working

    Try to do this:

    Open one terminal and type: tail -f /var/log/messages

    Then, after opening the first one (do not minimize it or close it, leave it open so you can see what happens, just rezise it to have both terminal on sight), open a second terminal
    and type: modeprobe -v i915 modeset=1

    Please post output of both.

    Luck.
    Last edited by maverik35; 02-07-2013 at 05:49 PM.

  5. #15
    Just burned their ISO
    Join Date
    Feb 2013
    Posts
    2

    Default Re: Intel integrated graphics are not working

    I have had the same problem, and it took me 3 days to figure out how to fix this. I'm booting from usb. Anyway here are the links I used follow this and it might help.

    http://www.tipslinux.com/info/repair...cktrack-5.html
    http://back-track-linux.blogspot.nl/...hen-using.html

    Goodluck

  6. #16
    Just burned their ISO
    Join Date
    Jan 2013
    Posts
    19

    Default Re: Intel integrated graphics are not working

    Quote Originally Posted by maverik35 View Post
    That is quiet interesting..You say it shifted about 3", but still it does not show it in lspci....Try again , but now without modeset = 1, just i915....
    doing it without modeset wont do anything.

  7. #17
    Just burned their ISO
    Join Date
    Jan 2013
    Posts
    19

    Default Re: Intel integrated graphics are not working

    Quote Originally Posted by maverik35 View Post
    Try to do this:

    Open one terminal and type: tail -f /var/log/messages

    Then, after opening the first one (do not minimize it or close it, leave it open so you can see what happens, just rezise it to have both terminal on sight), open a second terminal
    and type: modeprobe -v i915 modeset=1

    Please post output of both.

    Luck.
    trying this gives a black screen and i cant do anything., other than force shutdown i.e poweroff directly.

  8. #18
    Just burned their ISO
    Join Date
    Jan 2013
    Posts
    19

    Default Re: Intel integrated graphics are not working

    Quote Originally Posted by WepWapWee View Post
    I cant deduce exactly from what you wrote above, therefore I must say: you must make sure that when you issue "modprobe i915 modeset=1" command, you are completely in text mode (aka command line mode). This means, you call modeprobe cmd BEFORE you issue the startx command!
    Even if your screen gets shifted, try to do "startx" blindfold and see if the resolution gets fixed.



    This definetly means that your graphic card is NOT using the i915 kernel driver.
    yeah i am not running the command from CLI before startx, although i did fear that if i run it from if it shifted again then will become permanent coz it happend when i had installed gnome of bt5. suppose if it gets shifted is there anyway i ll be able to revert it back ?? srry. but i just need a backup plan coz i had already reinstalled it 4 times due to hit and try to fix graphics issue.

  9. #19
    Very good friend of the forum maverik35's Avatar
    Join Date
    Sep 2009
    Location
    Debian land
    Posts
    734

    Default Re: Intel integrated graphics are not working

    As you were posting before, you are able to get all the way to terminal mode after booting..If loded the intel module with modprobe i915 modeset =1 , it shifted (image) 3".

    Ok once you boot again, do not load the module with modprobe, do what I posted bebore, open 2 terminals:

    terminal 1: Open it with ctl+alt+F1 You will see the prompt..
    terminal 2: Open it with ctl+alt+F2 You will see the prompt..

    To switch in between the 2, just the same thing: ctl+alt+F1 or F2 accordingly

    In terminal 1, type: tail -f /var/log/messages

    Switch to terminal 2 and load the module: modprobe -v i915 modeset=1

    Now Switch back to terminal 1 and see what is going on with kernel when trying to load the i915...

    Try it..You need to know why kernel refuses to load module...

    Please try post output of both if possible..

  10. #20
    Just burned their ISO
    Join Date
    Jan 2013
    Posts
    19

    Default Re: Intel integrated graphics are not working

    Quote Originally Posted by maverik35 View Post
    As you were posting before, you are able to get all the way to terminal mode after booting..If loded the intel module with modprobe i915 modeset =1 , it shifted (image) 3".

    Ok once you boot again, do not load the module with modprobe, do what I posted bebore, open 2 terminals:

    terminal 1: Open it with ctl+alt+F1 You will see the prompt..
    terminal 2: Open it with ctl+alt+F2 You will see the prompt..

    To switch in between the 2, just the same thing: ctl+alt+F1 or F2 accordingly

    In terminal 1, type: tail -f /var/log/messages

    Switch to terminal 2 and load the module: modprobe -v i915 modeset=1

    Now Switch back to terminal 1 and see what is going on with kernel when trying to load the i915...

    Try it..You need to know why kernel refuses to load module...

    Please try post output of both if possible..

    I followed the steps as you said and here is the output:

    [drm] initialized drm 1.1.0 20060810
    i915 0000:02.0 : PCI INT A -> GSI 16
    [drm] supports vblank timestamp cachin
    [drm] Driver supports precise vblank t
    vgaarb : device changed decodes : PCI : 00
    fb : conflicting fb hw usage inteldrmfb vs EFI VGA - removing generic driver
    Console: Switching to colour dummy device 80*25
    fbcon : inteldrmfb (fb0) is primary device
    Console : switching to colour frame buffer device 170*48
    fb0 : inteldrmfb frame bufferdevice
    drm : registered panic notifier
    acpi device :41 : registered as cooling device9
    input: video bus as /devices/LNXSYSTM : 00/devices : 00/PNP0A08 : 00/LNXVIDEO : 00/input/input9
    ACPI : video Device [GFX0] (multi-head : yes rom : no post: no)
    [drm] initialized i915 1.6.0 20080730 to 0000:00:02.0 on mirror 0


    note: i would also like to know one thing that how could i be sure that i915 is the correct module to be loaded in my laptop. Because although it had intel HD 4000 integrated graphics but its chipset is 7 series/C210 series family which is displayed in lshw.

    Also, thanks for making efforts in solving my problem

Page 2 of 6 FirstFirst 1234 ... LastLast

Similar Threads

  1. Intel Integrated Graphics - Resolution Issue
    By Calamita in forum BackTrack 5 Beginners Section
    Replies: 4
    Last Post: 05-26-2012, 06:13 PM
  2. Replies: 2
    Last Post: 04-21-2012, 09:21 AM
  3. Replies: 0
    Last Post: 01-09-2012, 02:12 AM
  4. Replies: 28
    Last Post: 03-30-2011, 08:37 PM
  5. Screen resolution problem, Intel integrated graphics
    By Big Boss in forum Beginners Forum
    Replies: 3
    Last Post: 10-13-2010, 01:47 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •