Results 1 to 4 of 4

Thread: Wireless card problem (detailed)

  1. #1
    Just burned their ISO
    Join Date
    Nov 2012
    Posts
    1

    Default Wireless card problem (detailed)

    Hi,

    I'm going to start off by saying that I am no professional I'm just a young man whom is forcing himself to use BT5r3 and having some issues and would really appreciate some help on this as I have spent many many hours trying to fix it and have had no avail and hope that I will find someone here who can see I'm making an effort to learn on my own and just need a help.

    I want to try get my USB wireless card to work.
    BT5R3 (GNOME)32-bit installed on a laptop.

    Wifi-card ASUS WL-167g v3
    Code:
    Interface: USB
    
    
    
    FCC ID: MSQ-WL167GV3
    
    Chip 1: Realtek RTL8188SU
    
    
    Linux driver website.
    http://linuxwireless.org/en/users/Drivers/rtl819x
    
    
    Linux driver
    r8712u

    ifconfig (from my little understanding not needed but okay)
    Code:
    root@bt:~# ifconfig
    eth0      Link encap:Ethernet  HWaddr 00:15:c5:b2:47:32  
              UP BROADCAST MULTICAST  MTU:1500  Metric:1
              RX packets:0 errors:0 dropped:0 overruns:0 frame:0
              TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000 
              RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
              Interrupt:17 
    
    lo        Link encap:Local Loopback  
              inet addr:127.0.0.1  Mask:255.0.0.0
              inet6 addr: ::1/128 Scope:Host
              UP LOOPBACK RUNNING  MTU:16436  Metric:1
              RX packets:20002 errors:0 dropped:0 overruns:0 frame:0
              TX packets:20002 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:0 
              RX bytes:6425603 (6.4 MB)  TX bytes:6425603 (6.4 MB)
    iwconfig
    Code:
    root@bt:~# iwconfig
    lo        no wireless extensions.
    
    wlan1     unassociated  Nickname:"rtl_wifi"
              Mode:Managed  Access Point: Not-Associated   Sensitivity:0/0  
              Retry:off   RTS thr:off   Fragment thr:off
              Encryption key:off
              Power Management:off
              Link Quality:0  Signal level:0  Noise level:0
              Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
              Tx excessive retries:0  Invalid misc:0   Missed beacon:0
    
    wlan0     IEEE 802.11abg  ESSID:off/any  
              Mode:Managed  Frequency:2.427 GHz  Access Point: Not-Associated   
              Tx-Power=13 dBm   
              Retry  long limit:7   RTS thr:off   Fragment thr:off
              Encryption key:off
              Power Management:off
              
    eth0      no wireless extensions.
    lsusb
    Code:
    root@bt:~# lsusb
    Bus 005 Device 003: ID 1532:0109 Razer USA, Ltd Lycosa Keyboard
    Bus 005 Device 002: ID 413c:8126 Dell Computer Corp. Wireless 355 Bluetooth
    Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 004 Device 002: ID e0ff:0002  
    Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 001 Device 007: ID 0b05:1791 ASUSTek Computer, Inc. WL-167G v3 802.11n Adapter [Realtek RTL8188SU]
    Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    root@bt:~#
    airmon-ng
    Code:
    root@bt:~# airmon-ng
    
    
    Interface	Chipset		Driver
    
    wlan0		Intel 3945ABG	iwl3945 - [phy0]
    dmesg (took some of the info that i thought was important)(excuse my ignorance if it isn't valid or vital information is missing)
    Code:
    [ 1137.908652] generic-usb 0003:E0FF:0002.0007: input,hidraw2: USB HID v1.00 Mouse [A..... G3] on usb-0000:00:1d.2-1/input0
    [ 1137.914443] input: A..... G3 as /devices/pci0000:00/0000:00:1d.2/usb4/4-1/4-1:1.1/input/input15
    [ 1137.914680] generic-usb 0003:E0FF:0002.0008: input,hiddev0,hidraw3: USB HID v1.00 Keyboard [A..... G3] on usb-0000:00:1d.2-1/input1
    [ 1143.568117] usb 1-3: new high-speed USB device number 7 using ehci_hcd
    [ 1143.811677] r8712u: module is from the staging directory, the quality is unknown, you have been warned.
    [ 1143.813811] r8712u: DriverVersion: v7_0.20100831
    [ 1143.813831] r8712u: register rtl8712_netdev_ops to netdev_ops
    [ 1143.813834] r8712u: USB_SPEED_HIGH with 4 endpoints
    [ 1143.814403] r8712u: Boot from EFUSE: Autoload OK
    [ 1144.485037] r8712u: CustomerID = 0x0010
    [ 1144.485044] r8712u: MAC Address from efuse = bc:ae:c5:9b:12:f0
    [ 1144.485050] r8712u: Loading firmware from "rtlwifi/rtl8712u.bin"
    [ 1144.485976] usbcore: registered new interface driver r8712u
    [ 1580.718460] wlan0: deauthenticating from a0:21:b7:85:60:ca by local choice (reason=3)

    It might also be worth noting that when i enter Wicd and set it to use wlan1 instead of wlan0 when it tries to connect to my wifi it says bad paasword and wont connect.

    However i just swap it back to wlan0 and it works.

    I tried this but kept getting confused and lost around step 4
    Code:
    Who to get and install driver to WL-167g V3:
    
    http://ubuntuforums.org/showthread.php?t=1550135&page=2
    
    http://samiux.blogspot.com/2010/05/howto-realtek-8192su-usb-dongle.html
    HOWTO : RealTek 8192SU USB dongle (RTL8192SU) on Ubuntu 10.04
    D-Link DWA-131 Nano USB Wireless N adapter (USB dongle) is using RealTek 8192SU chip. However, it does not work on Ubuntu 10.04. This chip does work on Kernel 2.6.33. That is, this chip may work on Ubuntu 10.10 or later.
    
    The current version of RealTek 8192SU Linux driver is 0006 which is for Kernel 2.6.18 to 2.6.31 and dated 2010-03-25. However, Ubuntu 10.04 is using Kernel 2.6.32. You may encounter compile errors under Ubuntu 10.04. Don't panic, I have the solution.
    
    Step 1 :
    
    RealTek 8192SU driver from official site
    
    or download it from here.
    
    wget http://samiux.volospin.com/rtl8192SU_usb_linux_v2.6.0006.20100226.zip
    
    or
    wget
    http://www.itep.ru/ions/Arxiv/Fedora8/RTL8192SU_usb_linux_v2.6.6.0.20101111.zip
    
    Step 2 :
    
    sudo apt-get install unzip
    
    unzip rtl8192SU_usb_linux_v2.6.0006.20100226.zip
    
    cd rtl8712_8188_8191_8192SU_usb_linux_v2.6.0006.20100226/driver
    
    tar -xvzf rtl8712_8188_8191_8192SU_usb_linux_v2.6.0006.20100226.tar.gz
    
    cd rtl8712_8188_8191_8192SU_usb_linux_v2.6.0006.20100226
    
    Step 3 :
    
    cd include
    
    nano osdep_service.h
    
    add "#include <linux/sched.h>" to the file "osdep_service.h"
    
    the result looks like this :
    
    #ifndef __OSDEP_SERVICE_H_
    #define __OSDEP_SERVICE_H_
    
    #include <drv_conf.h>
    #include <basic_types.h>
    #include <linux/sched.h>
    //#include <rtl871x_byteorder.h>
    ......
    
    
    Step 4 :
    
    cd ..
    
    nano Makefile
    
    add "nullstring :=" under "export TOPDIR := $(PWD)"
    
    locate "ifeq ($(CONFIG_BUILT_IN), y)" and make changes to this ifeq block. The result looks like this :
    
    ifeq ($(CONFIG_BUILT_IN), y)
    include $(src)/config
    else
    ifeq ($(TOPDIR), $(nullstring))
    include config
    else
    include $(TOPDIR)/config
    endif
    endif
    
    The result of the first 19 lines is as the following :
    
    EXTRA_CFLAGS += -O1 -Wno-unused-variable -Wno-unused-value -Wno-unused-label -W$
    EXTRA_CFLAGS += -I$(src)/include -Wno-unused -Wno-unused-function
    
    CONFIG_BUILT_IN = n
    
    export TOPDIR := $(PWD)
    nullstring :=
    
    ifeq ($(CONFIG_BUILT_IN), y)
    include $(src)/config
    else
    ifeq ($(TOPDIR), $(nullstring))
    include config
    else
    include $(TOPDIR)/config
    endif
    endif
    
    ifeq ($(CONFIG_RTL8711), y)
    
    Step 5 :
    
    make clean
    make
    sudo make install
    
    Step 6 :
    sudo modprobe 8712u
    echo "8712u" | sudo tee -a /etc/modules
    
    The dongle will work now. Be keep in mind that when the Kernel is updated, you may require to re-compile the driver at Step 5.
    
    That's all! See you.
    There were other cases of this when i searched around on a few forums but the thread were just ignored and old.

    I know ignorance here is closely linked with stupidity but I'm trying to learn and to be simple its not easy but I'm just going to keep going until i learn it just like i did with anything else.

    Looking forward to any advice.

    Thanks for taking the time to help a young and linux addict in the making.

    Peace,

  2. #2
    Very good friend of the forum maverik35's Avatar
    Join Date
    Sep 2009
    Location
    Debian land
    Posts
    734

    Default Re: Wireless card problem (detailed)

    Read this: http://forum.aircrack-ng.org/index.php?topic=7908.0
    And then read this (spanish) just look at the method: http://foro.seguridadwireless.net/li...con-aircrack!/

    Another thing, there is this "beini" software to audit wifi AP's and they have a version specially for Realtek 8xxx chipset series..This is another option, just ggogle and search for the homepage.

    Luck..

  3. #3
    Just burned their ISO
    Join Date
    Nov 2012
    Posts
    1

    Default Re: Wireless card problem (detailed)

    I have too same problem like that..

    I use bt 5r3 32bit Gnome ...

    Here is my problem.. I don't know. how i slove.


    eth0 Link encap:Ethernet HWaddr 14:fe:b5:9e:a4:db
    UP BROADCAST MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
    Interrupt:47 Base address:0x2000

    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    inet6 addr: ::1/128 Scope:Host
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:4659 errors:0 dropped:0 overruns:0 frame:0
    TX packets:4659 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:1348306 (1.3 MB) TX bytes:1348306 (1.3 MB)

    mon0 Link encap:UNSPEC HWaddr BC-77-37-33-EB-FE-30-30-00-00-00-00-00-00-00-00
    UP BROADCAST NOTRAILERS RUNNING PROMISC ALLMULTI MTU:1500 Metric:1
    RX packets:33720 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:10837561 (10.8 MB) TX bytes:0 (0.0 B)

    wlan0 Link encap:Ethernet HWaddr bc:77:37:33:eb:fe
    inet addr:192.168.1.39 Bcast:192.168.1.255 Mask:255.255.255.0
    inet6 addr: fe80::be77:37ff:fe33:ebfe/64 Scope:Link
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:717292 errors:0 dropped:0 overruns:0 frame:0
    TX packets:458293 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:814718397 (814.7 MB) TX bytes:52565352 (52.5 MB)

  4. #4
    Very good friend of the forum maverik35's Avatar
    Join Date
    Sep 2009
    Location
    Debian land
    Posts
    734

    Default Re: Wireless card problem (detailed)

    Quote Originally Posted by mechag View Post
    I have too same problem like that..

    I use bt 5r3 32bit Gnome ...

    Here is my problem.. I don't know. how i slove.


    eth0 Link encap:Ethernet HWaddr 14:fe:b5:9e:a4:db
    UP BROADCAST MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
    Interrupt:47 Base address:0x2000

    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    inet6 addr: ::1/128 Scope:Host
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:4659 errors:0 dropped:0 overruns:0 frame:0
    TX packets:4659 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:1348306 (1.3 MB) TX bytes:1348306 (1.3 MB)

    mon0 Link encap:UNSPEC HWaddr BC-77-37-33-EB-FE-30-30-00-00-00-00-00-00-00-00
    UP BROADCAST NOTRAILERS RUNNING PROMISC ALLMULTI MTU:1500 Metric:1
    RX packets:33720 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:10837561 (10.8 MB) TX bytes:0 (0.0 B)

    wlan0 Link encap:Ethernet HWaddr bc:77:37:33:eb:fe
    inet addr:192.168.1.39 Bcast:192.168.1.255 Mask:255.255.255.0
    inet6 addr: fe80::be77:37ff:fe33:ebfe/64 Scope:Link
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:717292 errors:0 dropped:0 overruns:0 frame:0
    TX packets:458293 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:814718397 (814.7 MB) TX bytes:52565352 (52.5 MB)
    Please, read rules, you cannot use other people thread to post your problem, open a new thread to get help.

Similar Threads

  1. USB wireless card problem
    By arctyc in forum Beginners Forum
    Replies: 3
    Last Post: 02-26-2011, 08:14 AM
  2. Replies: 0
    Last Post: 12-20-2010, 12:12 AM
  3. Wireless card problem
    By djsbdjsb in forum OLD Newbie Area
    Replies: 2
    Last Post: 12-13-2009, 05:53 PM
  4. wireless card problem
    By fido13uk in forum OLD Newbie Area
    Replies: 5
    Last Post: 01-13-2008, 06:00 AM
  5. Replies: 10
    Last Post: 05-22-2007, 01:27 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •