Reaver question

[rs232]

I'm running backtrack5 R3 and currently testing reaver 1.4
Once it runs it get stuck at 90.90% first then 99.99%

On question I have is:

Does reaver need to get to 100% before finding anything or does 100% refer to any possible combination of 7 digits pin?

The reason why I'm asking is because if it get stuck at 90.90 and pin e.g. 99985677 could I just run from 99985678 onwards?

Appreciates
rs232

[anashlali]

I'm running backtrack5 R3 and currently testing reaver 1.4
Once it runs it get stuck at 90.90% first then 99.99%

On question I have is:

Does reaver need to get to 100% before finding anything or does 100% refer to any possible combination of 7 digits pin?

The reason why I'm asking is because if it get stuck at 90.90 and pin e.g. 99985677 could I just run from 99985678 onwards?

Appreciates
rs232

1. you can stop reaver any time with (( Ctrl+c )) and it w'll save your seassion automaticly, all you need is to run reaver again on the same Ap and it well start from last pin you got, make sure the AP still working!

[anashlali]

reaver saves its session automaticly just stop it (( Ctrl+c )), all you need is run it again on the same AP and it well start from last pin.

[sostentado]

i encountered same as your example. possibly, if reaver doesn't continue at all, it means WPS is not enabled. IMHO

[rs232]

Thanks both, that doesn't answer my question.

[Gitsnik]

Thanks both, that doesn't answer my question.

Issue... I think 84 on the reaver googlecode page describes almost exactly this. Go through the same diagnostic steps as there. Specifically, use the --pin switch with the valid pin to be sure that your version/ install is operating correctly.

[flatounet]

same here , got probleme with reaver ;
sometime session are not saved ;

reaver have to can resume manually and not with saved session ,
im tryed attack mon my network ,
session are not saved at 75%
and i cant restart reaver at 70 / 72% .....
saving system dont work well here..... (75% at 1 pin / 31 seconds = 4 day working ......)

i dont know where report this to reaver owner .....

[dAnKeL]

mine seems to be running very slow i used

reaver -i mon0 -b bssid -vv

(3seconds/pin)

been running 5 hours and only at 35% is there anyway to speed the process up?

[flatounet]

[+] 0.11% complete @ 2012-10-10 08:34:34 (13 seconds/pin)
[+] 0.15% complete @ 2012-10-10 08:36:49 (19 seconds/pin)
[+] 0.20% complete @ 2012-10-10 08:40:04 (25 seconds/pin)
[+] 0.24% complete @ 2012-10-10 08:41:19 (24 seconds/pin)
[+] 0.27% complete @ 2012-10-10 08:43:37 (25 seconds/pin)
[+] 0.32% complete @ 2012-10-10 08:47:52 (30 seconds/pin)
[+] 0.36% complete @ 2012-10-10 08:52:07 (33 seconds/pin)
[+] 0.41% complete @ 2012-10-10 08:53:22 (30 seconds/pin)
[+] 0.45% complete @ 2012-10-10 08:56:37 (31 seconds/pin)
[+] 0.50% complete @ 2012-10-10 08:58:52 (31 seconds/pin)
[+] 0.55% complete @ 2012-10-10 09:00:07 (29 seconds/pin)
[+] 0.59% complete @ 2012-10-10 09:03:22 (30 seconds/pin)
[+] 0.64% complete @ 2012-10-10 09:06:37 (31 seconds/pin)
[+] 0.68% complete @ 2012-10-10 09:07:51 (30 seconds/pin)
[+] 0.73% complete @ 2012-10-10 09:11:06 (30 seconds/pin)
[+] 0.77% complete @ 2012-10-10 09:13:21 (30 seconds/pin)
[+] 0.82% complete @ 2012-10-10 09:15:36 (30 seconds/pin)
[+] 0.86% complete @ 2012-10-10 09:19:52 (31 seconds/pin)
[+] 0.91% complete @ 2012-10-10 09:23:07 (31 seconds/pin)
[+] 0.95% complete @ 2012-10-10 09:24:21 (30 seconds/pin)
[+] 1.00% complete @ 2012-10-10 09:27:37 (31 seconds/pin)
[+] 1.05% complete @ 2012-10-10 09:31:52 (32 seconds/pin)
[+] 1.09% complete @ 2012-10-10 09:33:07 (31 seconds/pin)

1% / hour

i think box / plug limit speed login/rate ....
i dont really think it's possible to speedup this method ...

but i think reaver can be modded to attack more than 1 ap at time....

[rs232]

Does reaver need to get to 100% before finding anything or does 100% refer to any possible combination of 7 digits pin?