Hello

I am using Backtrack 5 R2 and i try to use from the wiki the dedected tutorial...

I follow the steps not using manual installation and when i am on Load drivers section i run:

Code:
cd /pentest/telephony/dedected/com-on-air_cs-linux
make node
Then i insert my pcmcia card Com on air and run:

Code:
make load
And i am getting an error here:

Code:
root@bt:/pentest/telephony/dedected/com-on-air_cs-linux# make load
insmod ./com_on_air_cs.ko && \
pccardctl insert 0
insmod: error inserting './com_on_air_cs.ko': -1 Invalid module format
make: *** [load] Error 1

Is this a problem with the software or i have to do something else to load my pcmcia drivers?

Some more info:

Code:
dmesg | tail -n50
Code:
root@bt:~# dmesg | tail -n50
[ 11.169901] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 11.169904] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 11.169908] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 11.169911] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.452058] pcmcia_socket pcmcia_socket0: pccard: PCMCIA card inserted into slot 0
[ 12.452074] pcmcia_socket pcmcia_socket0: cs: memory probe 0xfe200000-0xfea6ffff: clean.
[ 12.465753] pcmcia 0.0: pcmcia: registering new device pcmcia0.0 (IRQ: 3)
[ 12.465922] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: excluding 0x170-0x177 0x1f0-0x1f7 0x370-0x377
[ 12.467990] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: excluding 0x3f0-0x3f7 0x400-0x41f 0x480-0x4bf 0x4d0-0x4d7
[ 12.468612] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: excluding 0x820-0x87f
[ 12.469045] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[ 12.469817] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xcffff 0xe0000-0xfffff
[ 12.469876] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff: excluding 0xa0000000-0xa0ffffff
[ 12.469933] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff: excluding 0x60000000-0x60ffffff
[ 12.469994] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[ 13.006606] iwl3945 0000:03:00.0: loaded firmware version 15.32.2.9
[ 13.077913] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 13.080117] r8169 0000:02:00.0: eth0: link down
[ 13.080307] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 13.400003] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 13.400088] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X
[ 13.400124] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[ 14.768335] r8169 0000:02:00.0: eth0: link up
[ 14.768600] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 25.696029] eth0: no IPv6 routers present
[ 42.231375] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 42.346143] [drm] Initialized drm 1.1.0 20060810
[ 42.417559] [drm] radeon defaulting to userspace modesetting.
[ 42.418313] pci 0000:01:00.0: setting latency timer to 64
[ 42.418505] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 42.418508] [drm] No driver support for vblank timestamp query.
[ 42.418512] [drm] Initialized radeon 1.33.0 20080528 for 0000:01:00.0 on minor 0
[ 43.001050] [drm] Setting GART location based on new memory map
[ 43.001814] [drm] Loading R500 Microcode
[ 43.070933] [drm] Num pipes: 1
[ 43.070942] [drm] writeback test succeeded in 1 usecs
[ 118.450239] cdrom: sr0: mrw address space DMA selected
[ 118.644406] UDF-fs: Partition marked readonly; forcing readonly mount
[ 118.682928] UDF-fs: INFO Mounting volume 'New', timestamp 2012/04/23 17:59 (10b4)
[ 386.744679] com_on_air_cs: version magic '2.6.38 SMP mod_unload ELAN ' should be '3.2.6 SMP mod_unload CORE2 '
[ 554.545848] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 554.644110] r8169 0000:02:00.0: eth0: link down
[ 554.644122] r8169 0000:02:00.0: eth0: link down
[ 554.644472] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 554.707094] r8169 0000:02:00.0: eth0: link down
[ 554.707441] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 556.342863] r8169 0000:02:00.0: eth0: link up
[ 556.343199] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 566.960050] eth0: no IPv6 routers present
[ 689.106238] com_on_air_cs: version magic '2.6.38 SMP mod_unload ELAN ' should be '3.2.6 SMP mod_unload CORE2 '
Thank you