-=Xploitz=- TUTORIAL: E-Z Connect To WPA Personal With AES

[samsung]

Hey samsung! Possibly some good tidings I bring you this time. (I hope)

Just had someone in another on of my connection tutorials tell me that they had their router set to "n" mode. What mode is your AP in?? G/N---mixed?? Change it to mixed or g only and this might help.

Oh? I'll need to give that a try when I get around to it, I've still not got around to doing the last info you provided me constantly working & out partying lol - but I will make time soon to try this & either way will post the results fingers crossed

[samsung]

I got my @ss in gear & installed BT3 onto my hard drive rather than running from a live cd & it worked a treat in about 20 seconds, I created the wpa_supplicant.conf file, ran dhcpcd & bingo as you said it popped up ath0 connected !!!

Thanks again for all the help given

[-=Xploitz=-]

I got my @ss in gear & installed BT3 onto my hard drive rather than running from a live cd & it worked a treat in about 20 seconds, I created the wpa_supplicant.conf file, ran dhcpcd & bingo as you said it popped up ath0 connected !!!

Thanks again for all the help given

Whew!!!

Yep, a HD install is much better and more efficient than running it as a live CD.

I'm so very glad you got it working. I was pulling out my hair trying to figure out what you could have possibly been doing wrong.

[MaxHalz]

I do all the steps described by managing with my hardware parameters but when I hit enter after:

wpa_supplicant -w -Dwext -iwlan0 -c/etc/wpa_supplicant.conf

and then:

dhcpcd wlan0

it runs but no messages appear nor I am able to connect or nothing.
On airodump it says that a network is visible but it is as saw by kismet witouth and encrption and is open. I wasnt using kismet and this mode together. At my home wireless assistant finds my wpa network in seconds but this one witch is open doesnt. Also tried on some other network at my work but not suceded to conect with wifi assistant.

I configured my wpa_supplicant.conf as saw on some other page, aint sure if it goes together all of it but tried to connect it all.:

      ctrl_interface=/var/run/wpa_supplicant
  
      ctrl_interface_group=0
         
  
      #eapol_version=1
  
      #ap_scan=2
  
      #fast_reauth=1
   
       
  
      # Open Network any SSID
  
      network={
  
        ssid="ZyXEL"
  
        key_mgmt=NONE
  
      }
  
  
       
 
      # Single Key 64bit & 128bit WEP
  
      network={
  
        ssid="InsertSSID"
  
        key_mgmt=NONE
  
        wep_key0="InsertKey"
  
        wep_tx_keyidx=0
  
      }
  
       
  
      # WPA protected network, TKIP, AES & TKIP + AES
  
      network={
  
        #scan_ssid=1
  
        ssid="InsertSSID"
  
        proto=WPA
  
        key_mgmt=WPA-PSK
  
        pairwise=CCMP TKIP
  
        group=CCMP TKIP
  
        psk="InsertASCIIKey"
  
      }
  
       
  
      # WPA2 protected network, TKIP, AES & TKIP + AES
  
      network={
  
        #scan_ssid=1
 
        ssid="InsertSSID"
  
        proto=RSN
 
        key_mgmt=WPA-PSK

        pairwise=CCMP TKIP
 
        group=CCMP TKIP
  
        psk="InsertASCIIKey"
  
      }

Is it neccesary for me to even if it is open network to give it an ssid inside wpa_suplicant.conf

I also tried with giving it an ssid inside the .conf and ewen then nothing. Maybe wasnt trying that hard eh?

I use intel WIFI chipset and all other programs work fine on BT3.

[imported_=Tron=]

I do all the steps described by managing with my hardware parameters but when I hit enter after:

wpa_supplicant -w -Dwext -iwlan0 -c/etc/wpa_supplicant.conf

Which wireless card are you using?

[MaxHalz]

intel pro wireless 3945 ABG dual band.

Hope will help.
Also will try with other drivers supported by wpa_supplicant. Also tried intel drivers but it seems they are outdated witch I get from running wpa_supplicant.

[fifo_thekid]

when i execute

wpa_supplicant -w -D wext -i wlan0 -c/etc/wpa_supplicant.conf

i get

ioctl[SIOCSIWAUTH]: Operation not supported
WEXT auth param 4 value 0x0 - ioctl[SIOCSIWAUTH]: Operation not supported
WEXT auth param 5 value 0x1 - ioctl[SIOCGIWSCAN]: Resource temporarily unavailable
ioctl[SIOCGIWSCAN]: Resource temporarily unavailable
ioctl[SIOCGIWSCAN]: Resource temporarily unavailable
ioctl[SIOCGIWSCAN]: Resource temporarily unavailable
ioctl[SIOCGIWSCAN]: Resource temporarily unavailable
ioctl[SIOCGIWSCAN]: Resource temporarily unavailable
ioctl[SIOCGIWSCAN]: Resource temporarily unavailable
ioctl[SIOCGIWSCAN]: Resource temporarily unavailable
ioctl[SIOCGIWSCAN]: Resource temporarily unavailable
ioctl[SIOCGIWSCAN]: Resource temporarily unavailable
ioctl[SIOCGIWSCAN]: Resource temporarily unavailable
ioctl[SIOCGIWSCAN]: Resource temporarily unavailable
ioctl[SIOCGIWSCAN]: Resource temporarily unavailable
ioctl[SIOCGIWSCAN]: Resource temporarily unavailable
ioctl[SIOCGIWSCAN]: Resource temporarily unavailable
CTRL-EVENT-TERMINATING - signal 2 received
ioctl[SIOCSIWAUTH]: Operation not supported
WEXT auth param 5 value 0x0 - ioctl[SIOCSIWAUTH]: Operation not supported
WEXT auth param 4 value 0x0 - bt dhcpc #

i have intel pro wireless card on bt3 final

[GwWoYA]

When I do:

wpa_supplicant -w -Dwext -wlan0 -c/etc/wpa_supplicant.conf

It says that -w is not good :/. Something wrong with that.. just nothing happens. What i'm doing wrong?

Owyeah, I'm using Backtrack 4. I can't do it like that here?