Intel Centrino 6300 N driver install on Back Track 5

[crakkajakka15]

Hello all

I've been hitting google hard the last few days with no results. I have a Intel wireless 6300 N card installed on my laptop but airmon or back track dont seem to see the chipset and version. I need some direction on getting the correct drivers installed to work with the aircrack suite. Any help or where to start would be greatly appreciated. The card will connect to my home access point and work fine although I cant seem to get the card into monitor mode or any functionality out of the aircrack-ng suite

I read in one place that i needed to update the firmware of the card and was directed to intelwirelesslinux.org. There I downloaded and copied the iwlwifi-ucode-6000 and copied it into /lib/firmware with no result

root@bt:~# ifconfig wlan0
wlan0     Link encap:Ethernet  HWaddr 00:24:d7:f3:d9:f0  
          inet addr:10.0.1.10  Bcast:10.0.1.255  Mask:255.255.255.0
          inet6 addr: fe80::224:d7ff:fef3:d9f0/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:5546 errors:0 dropped:0 overruns:0 frame:0
          TX packets:4136 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:3562497 (3.5 MB)  TX bytes:757472 (757.4 KB)

output from lspci

02:00.0 Network controller: Intel Corporation Centrino Ultimate-N 6300 (rev 35)

airmon-ng start wlan0
Interface	     Chipset		Driver

[Reamer]

It isn't a problem with the card (most likely).

Try this:

Uninstall the aircrack-ng suite (airmon-ng is included in this) with this command:

 apt-get autoremove aircrack-ng

Then download the sources from the aircrack-ng website here:
http://www.aircrack-ng.org/
Extract the .tar file with this command:

 tar -xf aircrack-ng-1.1.tar.gz

You will need to update some of the SSL-dev files so run this before building from source:

 apt-get install libssl-dev

Enter the directory that was just extracted and then run:

 make
make install

Reboot and everything should be good to go now.

[crakkajakka15]

Thanks, I will give this a try here shortly. Any reason why these steps need done?

[Reamer]

Thanks, I will give this a try here shortly. Any reason why these steps need done?

Just something about the suite not being installed correctly the first time I'm guessing. I really don't know why, I just reinstalled it when I was having the problem and it was fixed.

[Andryuha]

Hello
i have the same problem with no devices shown under the three words "interface ... ..." when i enter the "airmon-ng" command
I've followed successfully all the steps you provided in the second post, but nothing changed
What could be the reason?

I am using Samsung R410 laptop with Windows Vista Home 32bit and running Backtrack 4 through VM Workstation

[KevinJ]

Thanks!!! That was a really useful trick.

[kjtw73]

Reamer's solution worked for me...Dell Lat E6520 dual boot (Win7) with the Intel Centrino 6300...all working fine after doing this...

It isn't a problem with the card (most likely).

Try this:

Uninstall the aircrack-ng suite (airmon-ng is included in this) with this command:

 apt-get autoremove aircrack-ng

Then download the sources from the aircrack-ng website here:
http://www.aircrack-ng.org/
Extract the .tar file with this command:

 tar -xf aircrack-ng-1.1.tar.gz

You will need to update some of the SSL-dev files so run this before building from source:

 apt-get install libssl-dev

Enter the directory that was just extracted and then run:

 make
make install

Reboot and everything should be good to go now.

[rshadows]

i am running a mac OSX lion. with parallels running backtrack 5. i am having this same problem but when i get to the tar -xf air crack-ng-1.1.tar.gz , it does nothing. it takes the input then the next line is the root enter. can someone tell me where i messed up please.

[JohnSilvers]

hi guys,
i have installed backtrack 5 on my virtual box but i dont get any result when i run the airmon-ng and the iwconfig command return 0 wlan0 result. please help.
i tried reinstalling the complete aircrack-ng-1.1 package but that didnt help

i have a intelHM76 chipset. please help or redirect to apprpriate thread that you know

[maverik35]

hi guys,
i have installed backtrack 5 on my virtual box but i dont get any result when i run the airmon-ng and the iwconfig command return 0 wlan0 result. please help.
i tried reinstalling the complete aircrack-ng-1.1 package but that didnt help

i have a intelHM76 chipset. please help or redirect to apprpriate thread that you know

Wifi internal cards are not supported by VM..You will need a USB wifi device...