What does dmesg say?Originally Posted by esieens
No PMCIA support
Hello,
I have a dell d620 laptop. My understanding is that I cannot use the Broadcom wifi chipset to inject packets so I want to use an old US Robotics USR5410 that I still have. I believe this PC card should be able to inject packets.
However, under KDE, the card is not recognised. When I look at the KinfoCenter it says that no pmcia controller has been detected.
The card works fine under windows.
Any idea what could be wrong?
Thanks
What does dmesg say?
"\x74\x68\x65\x70\x72\x65\x7a\x39\x38";
Dmesg
Thanks for the response.
DMESG output below (in 2 parts):-
Code:capability Allocate Port Service[0000:00:01.0:pcie00] Allocate Port Service[0000:00:01.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.0:pcie00] Allocate Port Service[0000:00:1c.0:pcie02] Allocate Port Service[0000:00:1c.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.1 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.1:pcie00] Allocate Port Service[0000:00:1c.1:pcie02] Allocate Port Service[0000:00:1c.1:pcie03] PCI: Setting latency timer of device 0000:00:1c.2 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.2:pcie00] Allocate Port Service[0000:00:1c.2:pcie02] Allocate Port Service[0000:00:1c.2:pcie03] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 vesafb: framebuffer at 0xd0000000, mapped to 0xf8d00000, using 6144k, total 65536k vesafb: mode is 1024x768x16, linelength=2048, pages=1 vesafb: protected mode interface info at 00ff:44f0 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 bootsplash 3.1.6-2004/03/31: looking for picture...<6>...no good signature found. Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device ACPI: AC Adapter [AC] (on-line) ACPI: Battery Slot [BAT0] (battery present) ACPI: Battery Slot [BAT1] (battery absent) input: Lid Switch as /class/input/input0 ACPI: Lid Switch [LID] input: Power Button (CM) as /class/input/input1 ACPI: Power Button (CM) [PBTN] input: Sleep Button (CM) as /class/input/input2 ACPI: Sleep Button (CM) [SBTN] ACPI: Video Device [VID] (multi-head: yes rom: no post: no) ACPI: Video Device [VID] (multi-head: yes rom: no post: no) ACPI: Video Device [VID2] (multi-head: yes rom: no post: no) ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu0Ist] [20060707] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu0Cst] [20060707] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: Thermal Zone [THM] (61 C) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A Floppy drive(s): fd0 is 1.44M floppy0: no floppy controllers found RAMDISK driver initialized: 16 RAM disks of 4444K size 1024 blocksize loop: loaded (max 255 devices) Compaq SMART2 Driver (v 2.6.0) HP CISS Driver (v 3.6.14) input: Macintosh mouse button emulation as /class/input/input3 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ide0: I/O resource 0x1F0-0x1F7 not free. ide0: ports already in use, skipping probe Probing IDE interface ide1... hdc: TSSTcorp DVD+/-RW TS-L632D, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 ide-floppy driver 0.99.newide Loading Adaptec I2O RAID: Version 2.4 Build 5go Detecting Adaptec I2O RAID controllers... Adaptec aacraid driver (1.1-5[2423]-mh3) scsi: <fdomain> Detection failed (no card) sym53c416.c: Version 1.0.0-ac qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options<6>QLogic Fibre Channel HBA Driver Emulex LightPulse Fibre Channel SCSI driver 8.1.11 Copyright(c) 2004-2006 Emulex. All rights reserved. Failed initialization of WD-7000 SCSI card! DC390: clustering now enabled by default. If you get problems load with "disable_clustering=1" and report to maintainers megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006) megaraid: 2.20.4.9 (Release Date: Sun Jul 16 12:27:22 EST 2006) megasas: 00.00.03.05 Mon Oct 02 11:21:32 PDT 2006 GDT-HA: Storage RAID Controller Driver. Version: 3.05 GDT-HA: Found 0 PCI Storage RAID Controllers 3ware Storage Controller device driver for Linux v1.26.02.002. 3ware 9000 Storage Controller device driver for Linux v2.26.02.008. nsp32: loading... st: Version 20061107, fixed bufsize 32768, s/g segs 256 ata_piix 0000:00:1f.2: version 2.00ac7 ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ] ACPI: PCI Interrupt 0000:00:1f.2[B] -> Link [LNKB] -> GSI 7 (level, low) -> IRQ 7 ata: 0x170 IDE port busy ata: conflict with ide1 PCI: Setting latency timer of device 0000:00:1f.2 to 64 ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xBFA0 irq 14 ata2: DUMMY scsi2 : ata_piix ata1.00: ATA-7, max UDMA/100, 156301488 sectors: LBA48 NCQ (depth 0/32) ata1.00: ata1: dev 0 multi count 8 ata1.00: configured for UDMA/100 scsi3 : ata_piix scsi 2:0:0:0: Direct-Access ATA SAMSUNG HM080HI AB10 PQ: 0 ANSI: 5 SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sd 2:0:0:0: Attached scsi disk sda I2O subsystem v1.325 i2o: max drivers = 8 I2O Configuration OSM v1.323 I2O Bus Adapter OSM v1.317 I2O Block Device OSM v1.325 I2O SCSI Peripheral OSM v1.316 I2O ProcFS OSM v1.316 Fusion MPT base driver 3.04.03 Copyright (c) 1999-2007 LSI Logic Corporation Fusion MPT SPI Host driver 3.04.03 Fusion MPT FC Host driver 3.04.03 Fusion MPT SAS Host driver 3.04.03 usbmon: debugfs is not available usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver PNP: No PS/2 controller found. Probing ports directly. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 raid6: int32x1 856 MB/s raid6: int32x2 916 MB/s raid6: int32x4 618 MB/s raid6: int32x8 578 MB/s raid6: mmxx1 2656 MB/s raid6: mmxx2 3071 MB/s raid6: sse1x1 1621 MB/s raid6: sse1x2 2173 MB/s raid6: sse2x1 3041 MB/s raid6: sse2x2 3423 MB/s raid6: using algorithm sse2x2 (3423 MB/s) md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 raid5: automatically using best checksumming function: pIII_sse pIII_sse : 7200.000 MB/sec raid5: using function: pIII_sse (7200.000 MB/sec) md: multipath personality registered for level -4 md: faulty personality registered for level -5 device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com device-mapper: multipath: version 1.0.5 loaded device-mapper: multipath round-robin: version 1.0.0 loaded device-mapper: multipath emc: version 0.0.3 loaded TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode ACPI: (supports S0 S3 S4 S5) Time: tsc clocksource has been installed. input: AT Translated Set 2 keyboard as /class/input/input4 Time: hpet clocksource has been installed. md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). Freeing unused kernel memory: 296k freed squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher squashfs: LZMA suppport for slax.org by jro aufs 20070219 ISO 9660 Extensions: Microsoft Joliet Level 3 Unable to load NLS charset utf8 Unable to load NLS charset utf8
Dmesg 2
Code:ISO 9660 Extensions: RRIP_1991A ISO 9660 Extensions: Microsoft Joliet Level 3 Unable to load NLS charset utf8 Unable to load NLS charset utf8 ISO 9660 Extensions: RRIP_1991A bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 87540 bytes,<6>...found (1024x768, 87432 bytes, v3). bootsplash: status on console 0 changed to on iTCO_vendor_support: vendor-support=0 iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (11-Nov-2006) iTCO_wdt: Found a ICH7-M TCO device (Version=2, TCOBASE=0x1060) iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) intel_rng: FWH not detected Linux agpgart interface v0.101 (c) Dave Jones shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1d.0: irq 10, io base 0x0000bf80 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKF] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.1: irq 11, io base 0x0000bf60 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 9 PCI: setting IRQ 9 as level-triggered ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKG] -> GSI 9 (level, low) -> IRQ 9 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.2: irq 9, io base 0x0000bf40 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ieee80211_crypt: registered algorithm 'NULL' input: PC Speaker as /class/input/input5 usb 1-2: new full speed USB device using uhci_hcd and address 2 ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI Interrupt 0000:00:1d.3[D] -> Link [LNKH] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.3: irq 5, io base 0x0000bf20 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com> agpgart: Detected an Intel 945GM Chipset. agpgart: AGP aperture is 256M @ 0x0 Yenta: CardBus bridge found at 0000:03:01.0 [1028:01c2] Yenta O2: res at 0x94/0xD4: 00/ea Yenta O2: enabling read prefetch/write burst usb 1-2: configuration #1 chosen from 1 choice hub 1-2:1.0: USB hub found hub 1-2:1.0: 4 ports detected Yenta: ISA IRQ mask 0x0018, PCI irq 11 Socket status: 30000820 Yenta: Raising subordinate bus# of parent bus (#03) from #04 to #07 pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff cs: IO port probe 0x2000-0x2fff: clean. pcmcia: parent PCI bridge Memory window: 0xe4000000 - 0xe9ffffff pcmcia: parent PCI bridge Memory window: 0xe0000000 - 0xe3ffffff ACPI: PCI Interrupt 0000:00:1f.3[B] -> Link [LNKB] -> GSI 7 (level, low) -> IRQ 7 ACPI: PCI Interrupt 0000:00:1b.0[A] -> Link [LNKF] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1b.0 to 64 bcm43xx driver sd 2:0:0:0: Attached scsi generic sg0 type 0 usb 1-2.3: new full speed USB device using uhci_hcd and address 3 usb 1-2.3: configuration #1 chosen from 1 choice hub 1-2.3:1.0: USB hub found hub 1-2.3:1.0: 3 ports detected pccard: CardBus card inserted into slot 0 cs: IO port probe 0xc00-0xcff: excluding 0xc80-0xc87 0xc90-0xc97 cs: IO port probe 0x820-0x8ff: clean. cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7 cs: IO port probe 0x100-0x3af: excluding 0x280-0x287 cs: IO port probe 0xa00-0xaff: clean. usb 1-2.3.2: new full speed USB device using uhci_hcd and address 4 usb 1-2.3.2: configuration #1 chosen from 1 choice ALSA /tmp/2.6.20/src-drivers/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:556: hda_intel: azx_get_response timeout, switching to polling mode... ACPI: PCI Interrupt 0000:00:1d.7[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 10, io mem 0xffa80000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 8 ports detected tg3.c:v3.72 (January 8, 2007) ACPI: PCI Interrupt 0000:09:00.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:09:00.0 to 64 eth0: Tigon3 [partno(BCM5752KFBG) rev 6002 PHY(5752)] (PCI Express) 10/100/1000Base-T Ethernet 00:18:8b:c9:88:29 eth0: RXcsums[1] LinkChgREG[1] MIirq[1] ASF[0] Split[0] WireSpeed[1] TSOcap[1] eth0: dma_rwctrl[76180000] dma_mask[64-bit] ACPI: PCI Interrupt 0000:0c:00.0[A] -> Link [LNKB] -> GSI 7 (level, low) -> IRQ 7 PCI: Setting latency timer of device 0000:0c:00.0 to 64 usb 5-2: new high speed USB device using ehci_hcd and address 2 usb 5-2: configuration #1 chosen from 1 choice hub 5-2:1.0: USB hub found hub 5-2:1.0: 4 ports detected usb 1-2: USB disconnect, address 2 usb 1-2.3: USB disconnect, address 3 usb 1-2.3.2: USB disconnect, address 4 usb 5-2.3: new full speed USB device using ehci_hcd and address 3 usb 5-2.3: configuration #1 chosen from 1 choice hub 5-2.3:1.0: USB hub found hub 5-2.3:1.0: 3 ports detected usb 5-2.3.2: new full speed USB device using ehci_hcd and address 4 usb 5-2.3.2: configuration #1 chosen from 1 choice lp: driver loaded but no devices found input: PS/2 Generic Mouse as /class/input/input6 fuse init (API version 7.8) Capability LSM initialized NTFS volume version 3.1. PM: Writing back config space on device 0000:09:00.0 at offset c (was f6040000, writing 0) NET: Registered protocol family 10 lo: Disabled Privacy Extensions usb 2-2: new full speed USB device using uhci_hcd and address 2 usb 2-2: configuration #1 chosen from 1 choice Initializing USB Mass Storage driver... scsi4 : SCSI emulation for USB Mass Storage devices usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usb-storage: device found at 2 scsi 4:0:0:0: Direct-Access G_Drive MassStorage Disk 2000 PQ: 0 ANSI: 0 CCS SCSI device sdb: 128000 512-byte hdwr sectors (66 MB) sdb: Write Protect is off sdb: Mode Sense: be 00 00 00 sdb: assuming drive cache: write through SCSI device sdb: 128000 512-byte hdwr sectors (66 MB) sdb: Write Protect is off sdb: Mode Sense: be 00 00 00 sdb: assuming drive cache: write through sdb: sdb1 sd 4:0:0:0: Attached scsi removable disk sdb sd 4:0:0:0: Attached scsi generic sg1 type 0 usb-storage: device scan complete
Remove your card, then reinsert it. Then run dmesg again and look through the last dozen or so lines...that should give you some more information about your card. It should look something like this (this is already in your dmesg but we're looking for a little more specific info):
Followed by a bunch of other related stuff.pccard: CardBus card inserted into slot #
"\x74\x68\x65\x70\x72\x65\x7a\x39\x38";
Nothing
I tried. No reaction apart from:-
Code:pccard: CardBus card inserted into slot 0 pccard: card ejected from slot 0 pccard: CardBus card inserted into slot 0 pccard: card ejected from slot 0
lspci tell you about any card in your system
This seems to show that upon inserting your card, there isn't anything else happening (no driver loading, etc.). It would seem you're SOL.
"\x74\x68\x65\x70\x72\x65\x7a\x39\x38";
lspci
Using lspci I see that my card is recognised:-
When I remove the card the Texas Instrument Network Controller disappears.Code:00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Express Memory Controller Hub (rev 03) 00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Express PCI Express Root Port (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01) 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 01) 00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev 01) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev 01) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev 01) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e1) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 01) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) Serial ATA Storage Controller IDE (rev 01) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) 01:00.0 VGA compatible controller: nVidia Corporation Quadro NVS 110M / GeForce Go 7300 (rev a1) 03:01.0 CardBus bridge: O2 Micro, Inc. OZ601/6912/711E0 CardBus/SmartCardBus Controller (rev 40) 04:00.0 Network controller: Texas Instruments ACX 111 54Mbps Wireless Interface 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5752 Gigabit Ethernet PCI Express (rev 02) 0c:00.0 Network controller: Broadcom Corporation Dell Wireless 1390 WLAN Mini-PCI Card (rev 01)
Could it be a driver problem?
Thanks
Firmware/Driver
Also I read a post:
ubuntuforums.org/showthread.php?t=75448&highlight=5410&page=2
People seems to have had problems with the driver & firmware for this pmcia card.
So I have installed an inf driver using ndiskwrapper and got the card recognized. However, using ndiskwrapper the card cannot be used in monitor mode.
Any idea what I could try next?
Thanks
BTW :- Am I right to believe I cannot do packets injection using the broadcan WLAN card?
Posting Permissions