using airodump-ng

[denzx03]

hi ive got a problem when im dumping in airodump-ng there is no other mac attached to the bssid there is just the bssid there and i cant get a handshake without it so how do i go about this, thanks

[lupin]

Can you describe some of the searches you have done and what things you have tried to resolve this problem?

[denzx03]

Can you describe some of the searches you have done and what things you have tried to resolve this problem?

yeah i 1st start my card airmon-ng start wlan0
then type airodump-ng wlan0
then airodump-ng -w capture -c 1 --bssid MAC wlan0

my problem is i only get the bssid mac i don't get the second mac ie not connected to a pc but if i go on my phone and try to connect to it, it will bring the mac of my phone up will this still give me the 4way handshake even if i haven't put the password in

[freemyggle]

Did you find your answer yet?

CH 1 ][ Elapsed: 24 s ][ 2011-04-17 16:40

BSSID......................PWR...Beacons #Data, #/s CH MB ENC CIPHER AUTH ESSID

00:XX:YY:ZZ:CC:A4 -66.....261............100 8 1 54e. WPA2 CCMP PSK D5X5WGG1-Wireless


BSSID...........................STATION........... ........PWR Rate Lost Packets Probes

00:XX:YY:ZZ:CC:A4........00:XX:YY:ZZ:A3:FB 0 0e- 0e 0 98

I think you're trying to find the station number. Is that showing up?

[Sh3r0Azur4]

hi ive got a problem when im dumping in airodump-ng there is no other mac attached to the bssid there is just the bssid there and i cant get a handshake without it so how do i go about this, thanks

yeah...me too...i cant do a handshake with the airodump....

[Sh3r0Azur4]

yeah..me too...i cant do a handshake with the airodump...

[YYaaSSeeRR]

hey guys my problem is when I type :
airmon-ng start eth1

interface chipset driver
eth1 broadcom wl(monitor mode enabled)

I need to know on which mode is it on>?
like: (monitor mode enabled on mon0)
plz help me

Edit:

Can you describe some of the searches you have done and what things you have tried to resolve this problem?

hey man plz help me before I break my laptop
I have installed the bt4 r2 and here is my problem with pics:
http://www9.0zz0.com/2011/04/20/17/251389426.png

and now when I type airodump-ng eth1 look what do I have:
http://www9.0zz0.com/2011/04/20/17/412804530.png

plz man help me and tell me how to fix it by a message to my e-mail ya200ya200@hotmail.com

I hope to got your reply
bye

[freemyggle]

Unless mistaken, eth1 applies to your ethernet connection. wlan0 or wlan1 applies to your wireless card. When doing airmon-ng start wlan0 (or 1), this command switches the card into monitor mode hence the output of mon0. From this point, all commands use mon0 as in airodump-ng mon0. To get the handshake you are seeking, a wireless device has to be connected to the AP via the key so the --deauth command can perform it's task of kicking said device off the network forcing it to log back into the network with the key it has on file.

To the original post, I am having the same problem as there is no wifi device connected to my AP, only a desktop that is hardwired which has no need of using the AP's wifi password. I will have to connect another wireless device so I can watch the --deauth command kick it off the network for a fraction of a second and capture the handshake. Then start perfecting the process of cracking the handshake .cap file. One step at a time I guess.