I know that there are dozens of posts about this, but I can't find the sloution, hope you can hel me.
I'm running the BT4 for vmware on vmware player on a Windows XP. I'm connected to the internet via a Linksys USB Wifi Stick. In my vmware settings, I have the connection as Bridge.

When I login and type /etc/init.d/networking start I get this:

[COMMENT]Configuring network interfaces...eth1: ERROR while getting interface flags: No such device
Internet Systems Consortium DHCP Client V3.1.1
Copyright 2004-2008 Internet Systems Consortium.
All rights reserved.
For info, please visit

SIOCSIFADDR: No such device
eth1: ERROR while getting interface flags: No such device
eth1: ERROR while getting interface flags: No such device
Bind socket to interface: No such device
Failed to bring up eth1.
eth2: ERROR while getting interface flags: No such device
Internet Systems Consortium DHCP Client V3.1.1
Copyright 2004-2008 Internet Systems Consortium.
All rights reserved.
For info, please visit

SIOCSIFADDR: No such device
eth2: ERROR while getting interface flags: No such device
eth2: ERROR while getting interface flags: No such device
Bind socket to interface: No such device
Failed to bring up eth2.
ath0: ERROR while getting interface flags: No such device
Internet Systems Consortium DHCP Client V3.1.1
Copyright 2004-2008 Internet Systems Consortium.
All rights reserved.
For info, please visit

SIOCSIFADDR: No such device
ath0: ERROR while getting interface flags: No such device
ath0: ERROR while getting interface flags: No such device
Bind socket to interface: No such device
Failed to bring up ath0.
wlan0: ERROR while getting interface flags: No such device
Internet Systems Consortium DHCP Client V3.1.1
Copyright 2004-2008 Internet Systems Consortium.
All rights reserved.
For info, please visit

SIOCSIFADDR: No such device
wlan0: ERROR while getting interface flags: No such device
wlan0: ERROR while getting interface flags: No such device
Bind socket to interface: No such device
Failed to bring up wlan0.
done.[/COMMENT]


Wnen I run ifconfig I get this:

[COMMENT]eth0 Link encap:Ethernet HWaddr 00:0c:29:c5:db:49
inet addr:169.234.178.5 Bcast:169.234.178.255 Mask:255.255.255.0
inet6 addr: fe80::20c:29ff:fec5:db49/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:99 errors:0 dropped:0 overruns:0 frame:0
TX packets:22 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:14190 (14.1 KB) TX bytes:4056 (4.0 KB)
Interrupt:19 Base address:0x2000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:48 errors:0 dropped:0 overruns:0 frame:0
TX packets:48 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4224 (4.2 KB) TX bytes:4224 (4.2 KB)
[/COMMENT]

And airmon-ng comes empty, just this:
Interface Chipset Driver

My second proble came when I installed vmware-tools, I couldn't open BT4 again, I got an error saying: cannot run in framebuffer mode
I had to install BT4 all over again.

Hope you can help me. Thanks!