Kismet configuration on Asus EeePC 1005HA

[whiterabbit7500]

I've read through 99% of the other "kismet config" help threads, and can't find any help with this. I'm running this on Ubuntu 9.1 on my 1005HA. I know it's not BT, but I figure I can find more help here then anywhere else.

lshw -C network output

*-network
       description: Wireless interface
       product: AR9285 Wireless Network Adapter (PCI-Express)
       vendor: Atheros Communications Inc.
       physical id: 0
       bus info: pci@0000:02:00.0
       logical name: wmaster0
       version: 01
       serial: 00:25:d3:72:d0:2b
       width: 64 bits
       clock: 33MHz
       capabilities: pm msi pciexpress bus_master cap_list logical ethernet physical wireless
       configuration: broadcast=yes driver=ath9k ip=10.1.1.3 latency=0 multicast=yes wireless=IEEE 802.11bgn
       resources: irq:17 memory:fbff0000-fbffffff
  *-network
       description: Ethernet interface
       product: Atheros AR8132 / L1c Gigabit Ethernet Adapter
       vendor: Attansic Technology Corp.
       physical id: 0
       bus info: pci@0000:01:00.0
       logical name: eth0
       version: c0
       serial: 90:e6:ba:20:ea:f9
       capacity: 100MB/s
       width: 64 bits
       clock: 33MHz
       capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.0.1-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair
       resources: irq:28 memory:f7fc0000-f7ffffff ioport:ec00(size=128)

.config file (The relevant part at least)

# Kismet config file
# Most of the "static" configs have been moved to here -- the command line
# config was getting way too crowded and cryptic.  We want functionality,
# not continually reading --help!

# Version of Kismet config
version=2007.09.R1

# Name of server (Purely for organizational purposes)
servername=Kismet

# User to setid to (should be your normal user)
#suiduser=your_user_here

# Do we try to put networkmanager to sleep?  If you use NM, this is probably
# what you want to do, so that it will leave the interfaces alone while
# Kismet is using them.  This requires DBus support!
networkmanagersleep=true

# Sources are defined as:
# source=sourcetype,interface,name[,initialchannel]
# Source types and required drivers are listed in the README under the
# CAPTURE SOURCES section.
# The initial channel is optional, if hopping is not enabled it can be used
# to set the channel the interface listens on.
# YOU MUST CHANGE THIS TO BE THE SOURCE YOU WANT TO USE
source=ath9k,wlan0,Wireless

Output I receive

whiterabbit@WR-netbook:/etc/kismet$ sudo kismet
Launching kismet_server: //usr/bin/kismet_server
Suid priv-dropping disabled.  This may not be secure.
No specific sources given to be enabled, all will be enabled.
Non-RFMon VAPs will be destroyed on multi-vap interfaces (ie, madwifi-ng)
Enabling channel hopping.
Enabling channel splitting.
FATAL: Unknown capture source type 'ath9k' in source 'ath9k,wlan0,Wireless'
Done.

I checked the driver name, which in my case is ath9k, set the interface to wlan0, and the name to Wireless. Should I be using something different? How can I get this working?

[Barry]

What does iwconfig give you?

[whiterabbit7500]

lo        no wireless extensions.

eth0      no wireless extensions.

wmaster0  no wireless extensions.

wlan0     IEEE 802.11bgn  ESSID:""
          Mode:Managed  Frequency:2.412 GHz  Access Point: Not-Associated
          Tx-Power=20 dBm
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Power Management:on
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

not seeing anything there that would help though. Should I be looking for something?

[Archangel-Amael]

I've read through 99% of the other "kismet config" help threads, and can't find any help with this. I'm running this on Ubuntu 9.1 on my 1005HA. I know it's not BT, but I figure I can find more help here then anywhere else.

I am sorry but we can not support Ubuntu.