Results 1 to 8 of 8

Thread: Tp-link wn422g

Hybrid View

  1. #1
    Just burned his ISO
    Join Date
    Feb 2009
    Posts
    2

    Default Tp-link wn422g

    Tp-link wn422g with chip zd1211 is not working.
    If start airmon-ng start wlan0, I get
    wlan0 ZyDAS 1211 zd1211rw - [phy0]SIOCSIFFLAGS: No such device

    If airodump-ng wlan0, I get "ioctl(SIOCSIFFLAGS) failed: Connection timed out"

    In BT3 is so not working, because is not detectect.

  2. #2
    Senior Member
    Join Date
    Aug 2007
    Posts
    916

    Default

    paste your lsusb output along with fcc id.

  3. #3
    Just burned his ISO
    Join Date
    Feb 2009
    Posts
    2

    Default

    Bus 001 Device 002: ID 0ace:1215 ZyDAS WLA-54L WiFi

  4. #4
    Just burned his ISO
    Join Date
    Sep 2008
    Posts
    7

    Default

    struggling the same on bt4:

    dmesg after plugging in:

    Code:
    usb 2-1: USB disconnect, address 4
    usb 2-1: new high speed USB device using ehci_hcd and address 5
    usb 2-1: configuration #1 chosen from 1 choice
    usb 2-1: reset high speed USB device using ehci_hcd and address 5
    phy3: Selected rate control algorithm 'pid'
    zd1211rw 2-1:1.0: phy3
    Code:
    # iwconfig wlan1
    wlan1     IEEE 802.11bg  ESSID:""
              Mode:Managed  Frequency:2.412 GHz  Access Point: Not-Associated
              Tx-Power=0 dBm
              Retry min limit:7   RTS thr:off   Fragment thr=2352 B
              Encryption key:off
              Power Management:off
              Link Quality:0  Signal level:0  Noise level:0
              Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
              Tx excessive retries:0  Invalid misc:0   Missed beacon:0
    Code:
    # ifconfig wlan1 up
    SIOCSIFFLAGS: No such device
    after the ifconfig, dmesg states:

    Code:
    usb 2-1: firmware: requesting zd1211/zd1211b_ub
    usb 2-1: firmware: requesting zd1211/zd1211b_uphr
    zd1211rw 2-1:1.0: RF MAXIM_NEW_RF 0x8 is not supported
    tried, patching, grabbing firmware, searched thoroughly through these forums, but failed. it just may be that the TP-LINK WN422g is a no go

    I hear success on ubuntu forums by using the ndiswrapper, but that doesnt support monitor mode does it?

  5. #5
    Just burned his ISO
    Join Date
    Sep 2008
    Posts
    7

    Default

    I have since been able to get this card to work with injection, but on ubuntu 9.04
    Which is 2.6.28-11-generic

    So, I tried this card on ubuntu 8.10, which failed firmware loading when I would ifconfig wlan1 up, which was the same problems I was receiving with BT4.

    When I stuffed around with 9.04 for fun, I discovered that the card didnt fail on ifconfig up, and was able to enter monitor mode flawlessly. However injection failed, but that was just a matter of patching the drivers:
    hxxp://wiki.d3xt3r01.tk/index.php/ZD1211rw_with_patches_for_aircrack-ng

    So my general understanding is that something in the kernels in 8.10 and bt4 dont like the zd1211rw drivers/firmware.

    Hope this aids anyone else with this card

  6. #6
    Just burned his ISO
    Join Date
    Sep 2008
    Posts
    19

    Default

    u should patch zd1211rw source code on BT4. zd1211rw driver can't recognise RF uw2453 in wn422g,though driver do support uw2453. here is a patched driver from one chinese wireless bbs,
    TL-WN322G+ for bt4-beta Driver(LZM).zip
    h t t p://my.xwtop.com/filedown/20090514/0998ff1a.1.zip

    aireplay-ng -2 is OK

  7. #7
    My life is this forum Snayler's Avatar
    Join Date
    Jan 2010
    Posts
    1,418

    Default

    Follow aircrack tutorial

    hxxp://forum.aircrack-ng.org/index.php?topic=5334.0

  8. #8
    Just burned his ISO
    Join Date
    Nov 2009
    Posts
    4

    Default

    hxxp://forum.aircrack-ng.org/index.php?topic=5334.0

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •