Results 1 to 10 of 12

Thread: problem with wireless :S

Hybrid View

  1. #1
    Just burned his ISO
    Join Date
    Jun 2008
    Posts
    14

    Lightbulb problem with wireless :S

    this is my firsts steps of wireless.
    i just buy a new laptop hp 6730s and i have problems with wireless drivers :S
    somehow i found some drivers and installed but when i run this commands this shows me:

    teo@teo-hp:~$ sudo airmon-ng start eth2


    Interface Chipset Driver

    eth2 UNKNOWN wl (monitor mode enabled)

    teo@teo-hp:~$ sudo airodump-ng eth2
    ioctl(SIOCSIWMODE) failed: Invalid argument

    ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211
    or ARPHRD_IEEE80211_PRISM instead. Make sure RFMON is enabled:
    run 'ifconfig eth2 up; iwconfig eth2 mode Monitor channel <#>'
    Sysfs injection support was not found either.



    why eth2 chipset is UNKNOWN? and why airodump-ng don't work
    pls help me,i'm new here


    00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
    00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
    00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
    00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03)
    00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03)
    00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03)
    00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03)
    00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03)
    00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03)
    00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03)
    00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 (rev 03)
    00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 03)
    00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03)
    00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03)
    00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03)
    00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03)
    00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03)
    00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93)
    00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03)
    00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03)
    02:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01)
    85:00.0 Ethernet controller: Marvell Technology Group Ltd. Unknown device 4357

  2. #2
    Good friend of the forums
    Join Date
    Jun 2008
    Posts
    425

    Default

    I get that on my ath0 interface.
    I belive that it means it can't go to monitor mode. Needed to sniff and do wep/wpa attack means.

  3. #3
    Just burned his ISO
    Join Date
    Jun 2008
    Posts
    14

    Default

    Quote Originally Posted by compaq View Post
    I get that on my ath0 interface.
    I belive that it means it can't go to monitor mode. Needed to sniff and do wep/wpa attack means.
    must have some solution :S

  4. #4
    Junior Member
    Join Date
    Mar 2008
    Posts
    96

    Default

    Lucky i was bored enough to lookup what kind of wireless card is in your laptop. I've determined that it should be the intel 5100. According to the HCL is it not supported by backtrack 3. You can try the new compat-wireless drivers, i've read that they can enable injection on your particular card.
    www,linuxwireless,org/en/users/Download#Wheretodownload
    the instructions are deadly simple to follow, you just download, unpack, make, make install and make load. Hope this fixes your problem.

    *edit*
    Make sure you get the drivers for kernels <= 2.6.26

  5. #5
    Junior Member
    Join Date
    Mar 2008
    Posts
    96

    Default

    ok then, now we know its a BCM4312. It should also work with the compat-wireless drivers though.

  6. #6
    Just burned his ISO
    Join Date
    Jun 2008
    Posts
    14

    Default

    Quote Originally Posted by thunderwing View Post
    ok then, now we know its a BCM4312. It should also work with the compat-wireless drivers though.
    yes but hot to fix this

    teo@teo-hp:~$ sudo airodump-ng eth2
    ioctl(SIOCSIWMODE) failed: Invalid argument

    ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211
    or ARPHRD_IEEE80211_PRISM instead. Make sure RFMON is enabled:
    run 'ifconfig eth2 up; iwconfig eth2 mode Monitor channel <#>'
    Sysfs injection support was not found either.

  7. #7
    Junior Member
    Join Date
    Mar 2008
    Posts
    96

    Default

    I understand that it should,

    Quote Originally Posted by markomk View Post
    teo@teo-hp:~$ sudo airmon-ng start eth2


    Interface Chipset Driver

    eth2 UNKNOWN wl (monitor mode enabled)
    but it doesn't.

    A question for the OP, are you using backtrack or another linux os with the aircrack-ng suite installed. I'm just asking because of your prompt.

  8. #8
    Senior Member
    Join Date
    Apr 2008
    Posts
    2,008

    Default

    Quote Originally Posted by thunderwing View Post
    I understand that it should,

    but it doesn't.

    A question for the OP, are you using backtrack or another linux os with the aircrack-ng suite installed. I'm just asking because of your prompt.
    Ah well now I understand what you are saying. Somehow I completely managed to miss that the OP already had tried using airmon-ng in his very first post.
    -Monkeys are like nature's humans.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •