Results 1 to 6 of 6

Thread: WG111v3 - How to install the driver?

  1. #1
    Just burned his ISO
    Join Date
    Aug 2008
    Posts
    2

    Default WG111v3 - How to install the driver?

    Hello. Yes, I'm new, and I have a question.

    I got a driver for my WG111v3 Netgear USB Stick, comiled it and now I'm stuck. airdriver-ng says that it is loaded but I can't get my stick to work with it. Infact, my stick is registered with "wmaster0" and my normal PC Card is registered with "wlan0", could anyone help me?

  2. #2
    Just burned his ISO
    Join Date
    Aug 2008
    Posts
    9

    Default

    Quote Originally Posted by psygate View Post
    Hello. Yes, I'm new, and I have a question.

    I got a driver for my WG111v3 Netgear USB Stick, comiled it and now I'm stuck. airdriver-ng says that it is loaded but I can't get my stick to work with it. Infact, my stick is registered with "wmaster0" and my normal PC Card is registered with "wlan0", could anyone help me?
    when you type iwconfig does your card show up in monitor mode?

    You should see something like this where I bolded it:

    ath1 IEEE 802.11g ESSID:""
    Mode:Monitor Channel:0 Access Point: Not-Associated
    Bit Rate:0 kb/s Tx-Power:19 dBm Sensitivity=0/3
    Retry: off RTS thr: off Fragment thr: off
    Encryption key: off
    Power Management: off
    Link Quality=16/94 Signal level=-77 dBm Noise level=-93 dBm
    Rx invalid nwid: 0 Rx invalid crypt: 0 Rx invalid frag: 0
    Tx excessive retries: 0 Invalid misc: 0 Missed beaco: 0

  3. #3
    Senior Member secure_it's Avatar
    Join Date
    Feb 2010
    Location
    在這兩者之間 BackTrack是4 FwdTrack4
    Posts
    854

    Default

    Connect USB Stick after properly booting up BT3 and if its Atheros based chipset then forget it wont work with Discovery/injection as madwifi is not supporting USB NIC yet.after attaching test using this

    airodump-ng wlan0
    aireplay-ng -9 wlan0

    let us know chipset model & the commands you are using.

  4. #4
    Member
    Join Date
    Nov 2007
    Posts
    220

    Default

    i THINK that is the card I use, and I have never had to isntal drivers, straight out the box for BT3 etc.
    wtf?

  5. #5
    Just burned his ISO voodoosau's Avatar
    Join Date
    Jul 2008
    Posts
    17

    Default

    see last post from xploitz on page 1 here:

    h**p://forums.remote-exploit.org/showthread.php?t=7361&highlight=wg111v3

    the v3 is not supported.

  6. #6
    ukdavid30
    Guest

    Default

    Quote Originally Posted by psygate View Post
    Hello. Yes, I'm new, and I have a question.

    I got a driver for my WG111v3 Netgear USB Stick, comiled it and now I'm stuck. airdriver-ng says that it is loaded but I can't get my stick to work with it. Infact, my stick is registered with "wmaster0" and my normal PC Card is registered with "wlan0", could anyone help me?
    I have tested wg111v3
    best for this adapter is backtrack 4 not 3
    if you want disable card in your pc
    modprobe -r and example modprobe -r iwlagn
    remove usb adapter and plug again
    airmon-ng
    you will see what you got
    if wlan0 then
    airmon-ng start wlan0 check if you got wlan0 monitor mode enabled or monitor mode on mon0
    if mon0 then
    airodump-ng mon0
    if wlan0
    airodump-ng wlan0
    generally first check which card you use in your pc maybe this card is better then wg111v3
    regards
    david

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •