Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: RT61 Injection

  1. #1
    Just burned his ISO
    Join Date
    Jul 2008
    Posts
    9

    Default RT61 Injection

    I am not sure if this driver can inject, I have
    Network controller: RaLink RT2600 802.11 MIMO, I just bought this card today
    so.. someone please give me some good news.. because when I try to run aireplay-ng to associate with my home connection
    Code:
    Sending Authentication Request
    it fails with.
    Code:
    02:22:24  Sending Authentication Request (Open System)
    Attack was unsuccessful. Possible reasons:
    
        * Perhaps MAC address filtering is enabled.
        * Check that the BSSID (-a option) is correct.
        * Try to change the number of packets (-o option).
        * The driver/card doesn't support injection.
        * This attack sometimes fails against some APs.
        * The card is not on the same channel as the AP.
        * You're too far from the AP. Get closer, or lower
          the transmit rate.
    I also disabled mac filter for the time to see if it worked.
    *crosses fingers* else how is the AIR-PCM350? would that do? what else is left for me to do with this card?

  2. #2
    Just burned his ISO
    Join Date
    Jul 2008
    Posts
    9

    Default

    hmm weird, I just got this working by reading a post that I missed, now its not working again... lest I know it works

  3. #3
    Member imported_pynstrom's Avatar
    Join Date
    May 2008
    Posts
    143

    Default

    http://wiki.remote-exploit.org/index.php/HCL:Wireless
    Code:
    ~# aireplay-ng --test <interface>
    When hungry, eat your rice; when tired, close your eyes. Fools may laugh at me, but wise men will know what I mean. -- Lin-Chi
    - - - - - - - -
    I slept once, it was a Tuesday.

  4. #4
    Just burned his ISO
    Join Date
    Jul 2008
    Posts
    9

    Default

    Ya, I read that.. anyways.. that doesn't work for me because I don't have any other connections on my router.. I just have one laptop with a wireless adapter thanx.

  5. #5
    Just burned his ISO
    Join Date
    Jul 2008
    Posts
    6

    Default

    Quote Originally Posted by Is44c View Post
    I am not sure if this driver can inject, I have
    Network controller: RaLink RT2600 802.11 MIMO, I just bought this card today
    so.. someone please give me some good news.. because when I try to run aireplay-ng to associate with my home connection
    Code:
    Sending Authentication Request
    it fails with.
    Code:
    02:22:24  Sending Authentication Request (Open System)
    Attack was unsuccessful. Possible reasons:
    
        * Perhaps MAC address filtering is enabled.
        * Check that the BSSID (-a option) is correct.
        * Try to change the number of packets (-o option).
        * The driver/card doesn't support injection.
        * This attack sometimes fails against some APs.
        * The card is not on the same channel as the AP.
        * You're too far from the AP. Get closer, or lower
          the transmit rate.
    I also disabled mac filter for the time to see if it worked.
    *crosses fingers* else how is the AIR-PCM350? would that do? what else is left for me to do with this card?
    I dont know If I can give you "good" news as I have similar problems, but I have had some success with reloading the drivers and changing the rate per the output there. Try 1M, that was the suggestion in previous aircrack-ng versions

  6. #6
    Just burned his ISO
    Join Date
    Jul 2008
    Posts
    6

    Default

    Ok, Not sure if you resolved your problem fully. But I was stumped with a problem of my own for some time, and just found a (really simple) solution. As this post was one that with the appropriate name Ill post it here.

    Im using a crappy generic pcmcia with Ralink b/g chipset and using rt61 drivers. The problem I was having was that all aireplay-ng -9 <interface> attempts I was running returned negative results. Now maybe Im jsut a total retard and this is obvious but, the solution is to use this:

    aireplay-ng <interface> -a <bssid>

    where a is the bssid of an AP.

    For some reasons it will only accurately test injection when you insert the bssid into the cmd. Dunno if this will help anyone, but I do hope so
    In playing around further last night, I realized that as I suspected I might be...Im retarded :S Disregard all that last info, and replace it with this ACCURATE and simple info:

    For the above described problem, the answer is stupid simple. Follow these steps in order shown (all couple of them :P)

    insert PCMCIA/USB card (Disregard if card is onboard)

    Code:
    bt ~ # airmon-ng start wlan0
    
    
    Interface       Chipset         Driver
    
    eth1            Broadcom        bcm43xx
    wlan0           Ralink b/g      rt61 (monitor mode enabled)
    
    bt ~ # aireplay-ng -9 wlan0
    11:24:50  Trying broadcast probe requests...
    11:24:52  No Answer...
    11:24:52  Found 1 AP
    
    11:24:52  Trying directed probe requests...
    11:24:52  00:00:00:00:00:00 - channel: 11 - 'MCCS'
    11:24:56  Ping (min/avg/max): 0.036ms/18.599ms/68.008ms Power: 0.00
    11:24:56  14/30:  46%
    
    11:24:56  Injection is working!
    If that doesnt work, run modprobe rt61 after airmon-ng.

    Yes, its that simple. Anyway, for those out there that are trying to overthink it as I was, good luck! :P

  7. #7
    Just burned his ISO
    Join Date
    Dec 2008
    Posts
    8

    Default

    I have a similar problem.
    First, i managed to make my card (D-link G510) work with injection, installing this driver rt61-cvs-dally.tar.gz. When i reboot my system injection doesn't work.

    Any ideas? Thanks.

  8. #8
    Just burned his ISO
    Join Date
    Dec 2008
    Posts
    8

    Default

    ^no one???

  9. #9
    Senior Member
    Join Date
    Apr 2008
    Posts
    2,008

    Default

    Quote Originally Posted by johnripper View Post
    I have a similar problem.
    First, i managed to make my card (D-link G510) work with injection, installing this driver rt61-cvs-dally.tar.gz. When i reboot my system injection doesn't work.

    Any ideas? Thanks.
    Which version of BT are you running? If you use either the live CD version or a plain vanilla USB installation the changes you make will not be persistent. If you on the other hand do use an installation with persistent changes it is possible that you need to manually load the upgraded driver.
    -Monkeys are like nature's humans.

  10. #10
    Just burned his ISO
    Join Date
    Dec 2008
    Posts
    8

    Default

    Quote Originally Posted by =Tron= View Post
    Which version of BT are you running? If you use either the live CD version or a plain vanilla USB installation the changes you make will not be persistent. If you on the other hand do use an installation with persistent changes it is possible that you need to manually load the upgraded driver.
    I am running BT3 and i have already installed it in my hard disk.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •