Page 1 of 3 123 LastLast
Results 1 to 10 of 24

Thread: Broadcom 4311 still not working for injection

  1. #1

    Unhappy Broadcom 4311 still not working for injection

    Unless I am doing something wrong, bcm43xx is still not injecting. I put it into monitor mode channel 6 found some APs on channel 6. Power is 0 or -1 (when I know it's en extremely strong signal), injection tests failed on -9. Tried aireplay-ng -1, failed. Oh well. Unless I am doing something wrong like not loading it right or something. My atheros has no problem with injection, unless the Broadcom needs more steps on the loadup.

  2. #2
    Senior Member imported_spankdidly's Avatar
    Join Date
    Feb 2006
    Posts
    1,031

    Default

    Best thing to do is get a better card. Even if you did get the broadcom to work, it's going to be flaky.
    I felt like bending the bars back, and ripping out the window frames and eating them. yes, eating them! Leaping, leaping, leaping! Colonics for everyone! All right! You dumb*sses. I'm a mental patient. I'm *supposed* to act out!

  3. #3

    Default

    I actually just bought the WUSB54g on ebay refurb. I just would love not to have stuff plugged into my laptop and just use the built-in card. I'll keep trying to get it to work. I ain't no quitter.

  4. #4
    Senior Member imported_spankdidly's Avatar
    Join Date
    Feb 2006
    Posts
    1,031

    Default

    get an internal atheros card then.
    I felt like bending the bars back, and ripping out the window frames and eating them. yes, eating them! Leaping, leaping, leaping! Colonics for everyone! All right! You dumb*sses. I'm a mental patient. I'm *supposed* to act out!

  5. #5
    Member imported_rokrmc's Avatar
    Join Date
    Aug 2007
    Posts
    155

    Default

    But its works for me....

  6. #6

    Default

    Quote Originally Posted by rokrmc View Post
    But its works for me....
    Just curious. What do you do after boot.

    I changed kismet.conf to bcm43xx,eth0,Broadcom 4311
    I ran kismet

    I also tried:
    airmon-ng start eth0 6
    ifconfig eth0 up
    aireplay-ng -9 eth0

  7. #7
    Senior Member imported_spankdidly's Avatar
    Join Date
    Feb 2006
    Posts
    1,031

    Default

    well, what's the error?
    I felt like bending the bars back, and ripping out the window frames and eating them. yes, eating them! Leaping, leaping, leaping! Colonics for everyone! All right! You dumb*sses. I'm a mental patient. I'm *supposed* to act out!

  8. #8
    Member imported_rokrmc's Avatar
    Join Date
    Aug 2007
    Posts
    155

    Default

    This is what i do after boot...

    Code:
    ifconfig eth1 down
    airmon-ng start eth1
    ifconfig eth1 up
    aireplay-ng -9 eth1
    make sure the ap signal is extremely strong......

  9. #9

    Default Nothing really

    Quote Originally Posted by spankdidly View Post
    well, what's the error?
    When I run aireplay -1 it can get association - gives me a list of stuff it can be
    aireplay -9 just fails, not explanation given

  10. #10

    Default

    If I try eth1 down or up I get a 'no such interface' error.

Page 1 of 3 123 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •