Typically on most IPW3945 machines, the wireless interface is eth1 and the wired interface is eth0.

After you do /sbin/ipw3945d-start, you can do a dmesg and at the end of it you should see if...

I believe if you just install without reformatting your disk, then your old files will only get over-written if they are of the same name of the new files from the final release. Your extra files in...

Yes you can, but you need to have the B|T CD handy.

Follow these steps (Step 1 and 2 are only incase you have not already partitioned your hdd) :

1) Boot up your BT hdd install and open a shell...

Can't recall offhand, but I just went down one date/version for the firmware and it fixed the problem.

This happened to my D-Link DWL-2000AP+ and also the Linksys you mentioned. I had to downgrade the firmware to stop them from DDOSing out after an injection attempt. Also note you should be monitoring...

Well do dmesg after you do your modprobe and see what it says, or you can try to force the module to load with modprobe -f ath_pci

Hi there, not sure what I can do to help, but I guess I can assist in making modules for some of the apps or contributing the few modules I already made.

4 hours? Doesn't look like you're doing any injection then. 400,000 IVs should take no more than 20 minutes to generate, unless you're in an area where the signal is really bad. In which case I don't...

You could probably learn a lot from this website :

http://www.grape-info.com/doc/linux/

not just for security but also for other aspects of basic linux running. The section on the security has...

Very possible. Check the threads on WEP cracking, you only need one card, so long as it can do monitoring and injection.

5 hours for 150, 000 IVs is too long - which means your injection is probably not working right or you're in an area where the signal isn't that great. Check your beacon count and see that its...

Yes there is a way. You boot from the floppy with the cd drivers. This assigns a drive letter to your CD rom, lets say its D:

Then you just :


d:
cd boot
cd dos
linux

EXT3 works all the time with qtparted or or gparted.

Sometimes you just have to show the machine who is the boss :)

Enjoy!

The RC4 is correct for the client. The RC5 wouldn't compile and its not much different, so decided to stick with RC4, its in the earlier posts.

Also if you're using B|T final, there should be no...

Speaking of Bart PE, has anyone seen www.u3.com - seems to me like BartPE/WinPE modified to run read-write on a USB device from a emulator of sorts like VMPlayer.

I think the question is do you have a machine powerful enough to generate the tables in a reasonable time frame? If not you might want to just spend the money to buy those tables.

"Working fine with MadWiFi? driver. Test on Debian"

This I believe means that its been tested to work on various versions of MadWifi (and should work for even MadWifi-ng). The tests were done on...

Hmmm thats strange. I did do a dual scope trial the other day it was ok, but I was on a desktop with significantly more memory - wonder if that has anything to do with it. Will test this out and post...

ndisw.mo in post #6. Its right there.

B|T only includes the client. So you can overwrite it - no need to uninstall it. The daemon is not included in B|T.

Whose instructions did you follow? You can download the ndisw.zip from the sites I listed in my post and try that. That one works for sure.

I've updated the module into a complete install, inclusive of the 'first user' and the CA. Previously you still had to run the nessus-mkcert and nessus-add-first-user, but no more. You don't even...

You might have better luck with this poor-man's antenna :

http://forums.remote-exploit.org/showthread.php?t=2431&highlight=cardboard

Cheaper and seems a lot easier to make and I know it works....

Well aircrack doesn't support all that many PCI cards but you can see the recommended ones here :

http://www.aircrack-ng.org/doku.php?id=faq#which_is_the_best_card_to_buy

I'd say your best bet...