Printable View
Basically I'm running BT5 in virtual box and I have a USB wireless adapter I want to connect and use in it.
I have added it to the list of USB devices in the settings but when I plug it in... Nothing happens. I cannot search for wireless networks either. Anybody else every experience this problem?
once its connected it gets desconnected from windows
u cant searsh there unless inside the v box
soory for my bad english
:)
If you have as you said connected it to your virtual system and it is not still kicking around in your other OS, then you likely need to enable it. What do you see if you type "ifconfig" in terminal? Can you paste the contents for us? And why are you using a USB device, and not say NAT? Are you going to be pentesting wireless networks?
I've had more than 6 people confirm that the wireless adapter is "plug and play" with backtrack.
I just don't understand why I can't get it to work when using a VM?
Is there any bit of information I can post that anybody would find useful? Thanks again.
im not sure 100% to understand you
i think you use bt5 in vmware ?
start your system ,and in player you can see removable device go on it
and you have to see your hardware in , click connect , hardware will be disconect from windows
and working on linux ( bt5r3 gnome vm 32 ) here working fine on vmware player 5.0.0 build-812388 / windows 7 (64) with awus036h
i hope have help you.
need more info, like if you are if using vm or vmware, 32 or 64 bit distro, if you already install the guest-additions and extension packs if using vm?..You need the packs to be able to work with usb ports.
if using vm machine , did you add user to vxboxuser group? or is the user in vxboxuser?..Need to be in that group to see usb ports..
Luck.
Thank you for the many replies.
I will try to provide as much info as I can think of.
Yes, I am trying to perform pentesting on wireless networks.
I have BT5R3 64bit running on Oracle Virtual Box: https://www.virtualbox.org/. I have installed guest and extensions, USB seems to work fine with the VM.
When I connect the USB adapter to the VM it does disconnect from windows like you say...
IFCONFIG says this:
Code:eth0 Link encap:Ethernet HWaddr 08:00:27:60:f7:37
inet6 addr: fe80::a00:27ff:fe60:f737/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:3888 (3.8 KB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:77 errors:0 dropped:0 overruns:0 frame:0
TX packets:77 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:5417 (5.4 KB) TX bytes:5417 (5.4 KB)
Is there anything else I missed?
Thank you again for helping :)
That does not list a wireless USB dongle. So it looks like Backtrack is not seeing it. If wireless dongle was showing up you would see something like "wlan0".
Did you started the network services?...Need to see wifi interfaces...And as Raskolnikov pointed out, your wifi iface is not being seen by Kernel (udev module)...
Try starting services: /etc/init.d/networking start
If it doesn't work, refer here please: https://www.virtualbox.org/wiki/Downloads#manual
Here you have a section about: linux, Windows, Unix..Go to Windows section, it's all there, from installation, USB ports, Guest Additions etc to Troubleshooting. Great guide..All you need....
Hope it helps.
Luck...
Basically, some USB devices may not working well under VirtualBox when it is enabled USB 2.0. Try to deselect USB 2.0 and enabled the USB feature.Quote:
Originally Posted by TopCaliber
You are required to install the Extension Pack for the host and Additional ISO for guest.
When you plug in the USB device, your host computer may caught the USB device. You are required to go to the VirtualBox menu --> Devices --> USB Devices to select the USB dongle.
Finally, make sure your wireless USB dongle is compatible with BackTrack 5 r3.
Samiux