Is my CPU compatible with BT5?

Code:

---

fdisk -l

---

this will show all usb and hardrives

Quote:

---

Originally Posted by r083rt

Code:

---

fdisk -l

---

this will show all usb and hardrives

---

I tried that and it didn't show up

Quote:

---

Originally Posted by r083rt

hmmm you broke it :) my head is fried let me think theres a way around it it happend me a couple of ytimes with usb need to think ill go an get a cup of tea and try to remember

its a real simple fix lol but for the life of me I cant rememer


r083rt

---

Thanks very much. Please get back to me with that solution!

Any news, r083rt?

Code:

---

modprobe usb-uhci
modprobe usb-ohci
modprobe usb-storage

---

run dmesg

Code:

---

dmesg

---

you show get some output like this

Code:

---

Type:  Direct-Access                      ANSI SCSI revision: 00
SCSI device sdb: 78242976 512-byte hdwr sectors (40060 MB)
sdb: assuming drive cache: write through
SCSI device sdb: 78242976 512-byte hdwr sectors (40060 MB)
sdb: assuming drive cache: write through
 sdb: sdb1
sd 2:0:0:0: Attached scsi disk sdb
usb-storage: device scan complete

---

now lets

Code:

---

fdisk -l | grep sdb              (sdb is the output yours might be differnet check the output of dmesg)

---

output

Code:

---

Disk /dev/sda doesn't contain a valid partition table
Disk /dev/sdb: 40.0 GB, 40060403712 bytes
/dev/sdb1              1        4870    39118243+  c  W95 FAT32 (LBA)

---

now mount the usb

Code:

---

mount /dev/sdb1 /mnt

---

note (sdb1)maynot be yours it just an example

then do as above delete the partitons and format

r083rt

when i type modprobe usb-uci, it says FATAL: Module usb_uhci not found. and the same thing happens when i type modprobe usb-ohci. when i type modprobe usb-storage, it says nothing and just goes to another line so i can type a new command. when i type dmesg, it says a bunch of stuff but i just copied the end where it mentions usb. this is what it says:

Quote:

---

4061.848954] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 4061.932266] b44 ssb1:0: eth0: powering down PHY
[ 4061.946023] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4062.999895] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 4071.156073] usb 1-1: device not accepting address 2, error -110
[ 4071.156155] usb 1-1: USB disconnect, address 2
[ 4071.156189] scsi 2:0:0:0: Device offlined - not ready after error recovery
[ 4071.268089] usb 1-1: new high speed USB device using ehci_hcd and address 3
[ 4074.480776] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 4074.556263] b44 ssb1:0: eth0: powering down PHY
[ 4074.570072] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4074.720105] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 4077.208834] wlan0: authenticate with 00:1c:10:31:b8:6e (try 1)
[ 4077.210461] wlan0: authenticated
[ 4077.210794] wlan0: associate with 00:1c:10:31:b8:6e (try 1)
[ 4077.212889] wlan0: RX AssocResp from 00:1c:10:31:b8:6e (capab=0x411 status=0 aid=2)
[ 4077.212897] wlan0: associated
[ 4077.214532] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 4086.380100] usb 1-1: device descriptor read/64, error -110
[ 4087.888044] wlan0: no IPv6 routers present
[ 4101.596116] usb 1-1: device descriptor read/64, error -110
[ 4101.812100] usb 1-1: new high speed USB device using ehci_hcd and address 4
[ 4116.924056] usb 1-1: device descriptor read/64, error -110
[ 4132.140067] usb 1-1: device descriptor read/64, error -110
[ 4132.360073] usb 1-1: new high speed USB device using ehci_hcd and address 5
[ 4142.768064] usb 1-1: device not accepting address 5, error -110
[ 4142.880083] usb 1-1: new high speed USB device using ehci_hcd and address 6
[ 4153.288071] usb 1-1: device not accepting address 6, error -110
[ 4153.288108] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 4153.556083] usb 2-1: new full speed USB device using uhci_hcd and address 2
[ 4168.668083] usb 2-1: device descriptor read/64, error -110
[ 4183.884082] usb 2-1: device descriptor read/64, error -110
[ 4184.100106] usb 2-1: new full speed USB device using uhci_hcd and address 3
[ 4199.212062] usb 2-1: device descriptor read/64, error -110
[ 4214.428091] usb 2-1: device descriptor read/64, error -110
[ 4214.644082] usb 2-1: new full speed USB device using uhci_hcd and address 4
[ 4225.052070] usb 2-1: device not accepting address 4, error -110
[ 4225.164074] usb 2-1: new full speed USB device using uhci_hcd and address 5
[ 4235.572046] usb 2-1: device not accepting address 5, error -110
[ 4235.572084] hub 2-0:1.0: unable to enumerate USB device on port 1

---

So is this good or bad? What do I do from here?

Quote:

---

Originally Posted by yomama07024

Where to I save file to when using persistence?
Can I save them on the desktop and the next time I boot, they'll still be there?

While booting, it says:
BusyBox v1.13.3 (Ubuntu 1:1.13.3-1ubuntu11) built-in shell (ash)
Enter 'help' for a list of built-in commands.

(initramfs) Can not mount /dev/loop0 (/cdrom/casper/filesystem.squashfs) on //filesystem.squashfs

What does this mean?

---

Did someone tell me how i can resolve this problem?

Squashfs its a highly compressed system, the warning meaning it could not decompress the file and mount during start up.
You should prepare the USB to install the ISO. Meaning you need to format it so it will boot, personally I used YUMI, the windows version, note some version of YUMI are old and dont support BT5, this one worked for me, even I used a microsd card.
Yumi offers the option to format the USB stick.
Also it's important to check the checksum of the ISO. Also if you have problems after installation with your CPU, look using synaptic for Intel Microcode, which updates the microcode during boot, when starting the devices.

http://www.pendrivelinux.com/yumi-mu...t-usb-creator/

Greetings,
The Problem is not with the Linux. Its with BIOS. I had this problem too. What you need to do is Just Start The BIOS and then according to what Mother Board you are using you will have to ENABLE "Virtualization Tech". It is disabled for many computers as a result it give that error. Check Out Google on how to do It according to your Board.
Hope this Helps.