No airodump-ng acting after making airmon-ng
Hi all .. hope u doing good, am facing a problem in my network card on laptop (toshiba satellite)
after typing
iwconfig in shell, i get
Code:
root@bt:~# iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11 ESSID:"ThomsonE2A46B" Nickname:""
Mode:Managed Frequency:2.412 GHz Access Point: 00:1F:9F:D3:1F:EB
Bit Rate=54 Mb/s Tx-Power:24 dBm
Retry min limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Managementmode:All packets received
Link Quality=5/5 Signal level=-33 dBm Noise level=-83 dBm
Rx invalid nwid:0 Rx invalid crypt:3 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
so that eth1 is my wireless network card
i want to make airodump-ng .. so i made airmon-ng start eth1 and got
Code:
root@bt:~# airmon-ng start eth1
Interface Chipset Driver
eth1 Broadcom wl (monitor mode enabled)
after that i type airodump-ng eth1 to see my wireless router so i get this
Code:
root@bt:~# airodump-ng eth1
ioctl(SIOCSIWMODE) failed: Invalid argument
ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211,
ARPHRD_IEEE80211_FULL or ARPHRD_IEEE80211_PRISM instead. Make
sure RFMON is enabled: run 'airmon-ng start eth1 <#>'
Sysfs injection support was not found either.
!!!!!!!!!!!
any idea guys !! ??
where is the problem .. by the way .. am using bt r1 wich not updated .. does the update solves the problem .. or there is another way
and special thanks
btw .. my card as shown in lspci is Broadcom Corporation BCM4313 802.11b/g LP-PHY (rev 01)
AW: No airodump-ng acting after making airmon-ng
Did you try
instead of
since airmon-ng said monitor mode was enabled on wl?
Cheers
AW: No airodump-ng acting after making airmon-ng
http://www.backtrack-linux.org/forum....html?langid=3
Also try this. Sometimes when you type "airodump-ng [wireless card name]" you get an error message but when you type "airodump-ng mon0" it works.
so : "airodump-ng mon0" after you did "airmon-ng start eth1".
AW: No airodump-ng acting after making airmon-ng
thanks for replying .. Carnivore: yes i did it .. but nothing .. it says that monitor mode is not enabled ...
LHYX1: yes i tried also..but as i read that driver wl is not working with aircrack tool ... but the driver b43 is .. so need to move from wl to b43 so that it can works .. and am looking and searching also .. and any solution could help .. post it here
thanks again
AW: No airodump-ng acting after making airmon-ng
i have found that its not supported by aircrack till now .. so am gonna buy new card :D ... only this list
14e4:4311 b43/wl
14e4:4313 2.6.33+
14e4:4315 2.6.33+
14e4:4301 b43legacy B
14e4:4306 G
14e4:4320 G
14e4:4307 b43 G
14e4:4312 G
14e4:4318 G
14e4:4319 G
14e4:4320 G
14e4:5354 G
cu guys :D
